Single Pillow Block - Heavy Series - Houston Bearing and Supply

KETCHIE-HOUSTON, INC. PAGE 92
Insert Bearings - Standard Series - Self Aligning Ring
Used in the Following Unit:
• KH-4240 thru KH-4253 (SAL Type)
Features:
• Wide Inner Ring
• Self Aligning Ring Fitted to Outside Diameter
• Eccentric Locking Collar
Replaces Fafnir SM-KS
TO ORDER, SPECIFY KETCHIE-HOUSTON OR COMPETITOR’S PART NUMBER
Ketchie Replaces Bore (1) O.D Ring Widths Approx.
Houston Fafnir A B C D E&F G H J K N Unit
Inner Outer Wt.
in. in. in. in in. in. in. in. in. in.
mm mm mm mm mm mm mm mm mm
SWE100SR SM1100KS 1 2.2441 1 3 / 8 .591 11 / 16 1.293 5
/ 32 1 1 / 2
17
/ 32 1 3 / 4
57 34.93 15 17.5 32.84 4.0 38.1 43.5 44.4 .75
SWE103SR SM1103KS 1 3 / 16 2.6772 1 7 / 16 .630
23
/ 32 1.540 5
/ 32 1 3 / 4
5
/ 8 1 29 / 32
68 36.51 16 18.3 39.12 4.0 44.4 15.9 48.4 1.25
SWE104SR SM1104KS 1 1 / 4 3.1102 1 31 / 64 .669 .742 1.816 5
/ 32 2 1 / 8
11
/ 16 2 1 / 64
SWE107SR SM1107KS 1 7 / 16 79 37.70 17 18.85 46.13 4.0 54.40 17.5 51.2 1.75
SWE108SR SM1108KS 1 1 / 2 3.4646 1 11 / 16 .709
27
/ 32 2.058 3
/ 16 2 3 / 8
23
/ 32 2 7 / 32
88 42.86 18 21.4 52.27 4.8 60.3 18.3 56.4 2.25
SWE111SR SM1115KS 1 15 / 16 3.9370 1 15 / 16 .787
31
/ 32 2.474 3
/ 16 2 3 / 4
23
/ 32 2 15 / 32
100 49.21 20 24.6 62.84 4.8 69.9 18.3 62.7 2.75
SWE203SR SM1203KS 2 3 / 16 4.3307 2 3 / 16 .827 1 3 / 32 2.747 3
/ 16 3
13
/ 16 2 13 / 16
110 55.56 21 27.8 69.77 4.8 76.2 20.6 71.4 4.00
SWE207SR SM1207KS 2 7 / 16 4.7244 2 7 / 16 .866 1 7 / 32 3.011 1
/ 4 3 5 / 16 7
/ 8 3 1 / 16
120 61.91 22 31.0 76.48 6.4 84.1 22.2 77.8 4.50
SWE211SR SM1211KS 2 11 / 16 5.5118 2 11 / 16 .945 1 11 / 32 3.422 1
/ 4 3 13 / 16
15
/ 16 3 3 / 8
140 68.26 24 34.1 86.92 6.4 96.8 23.8 79.4 6.75
SWE215SR SM1215KS 2 15 / 16 5.7087 2 15 / 16 .984 2 15 / 32 3.619 1
/ 4 4
15
/ 16 3 5 / 8
145 74.61 25 37.3 91.92 6.4 101.6 23.8 92.1 8.00
SWE303SR SM1303KS 3 3 / 16 6.1024 3 3 / 16 1.024 1 19 / 32 3.874 1
/ 4 4 3 / 8 1 3 15 / 16
155 80.96 26 40.5 98.40 6.4 111.1 25.4 100.0 9.25
SWE307SR SM1307KS 3 7 / 16 6.4961 3 7 / 16 1.102 1 23 / 32 4.127 1
/ 4 4 7 / 16 1 4 3 / 16
165 87.31 28 43.7 104.83 6.4 112.7 25.4 106.4 10.50
SWE315SR SM1315KS 3 15 / 16 7.8740 3 15 / 16 1.339 1 31 / 32 4.876 1
/ 4 5 1 / 2 1 1 / 4 4 15 / 16
200 100.01 34 50.0 123.85 6.4 139.7 31.8 125.4 20.00
(1)
Bore Tolerance: 1” - 2 3 /16", nominal to +.0005”, +.013 mm; 2 1 /4” - 3 3 /16", nominal to +.0006”, +.015mm
3 1 /4" - 3 15 /16", nominal to +.0007”, +.018 mm
Recommended shaft tolerances: 1” - 1 15 /16", nominal to – .0005", – .013 mm;
2” - 3 15 /16", nominal to – .0010", – .025 mm