Single Pillow Block - Heavy Series - Houston Bearing and Supply

PAGE 33
Pillow Block - Standard Series - High Temperature
Special Base to Center Height
Replaces Fafnir LSA
This Ketchie-Houston standard series high
temperature pillow block has a special base to
center height. These units are designed for
applications in which the operating temperature
exceeds 250˚F.
The units are equipped with a standard series
wide inner ring bearing, high temperature seals
and high temperature grease.
KETCHIE-HOUSTON, INC.
TO ORDER, SPECIFY KETCHIE-HOUSTON OR COMPETITOR’S PART NUMBER
Ketchie Replaces Shaft A B C D E F G H J K N S Bolt Bearing Approx.
Houston Diam. Size Number Unit
Wt.
Fafnir in. in. in. in in. in. in. in. in. in. in. in. in. in. lbs.
mm mm mm mm mm mm mm mm mm mm mm mm mm mm
KH-1362-0-10A LSA 3
/4 1 3 /4 3 1 23 /32 2 1 /2 5 6 1 /2 2 9 9 3
/16 /16 /4 1 5 /16 1 3 1
/64 /2 GSWE012HHS 3.00
20 44.45 76.2 43.7 63.5 127.0 165.1 50.8 14.3 14.3 19.0 33.3 27.8 12.7
9
/16
7
/8
15
/16 2 3 3 /8 1 3 /4 2 3 /4 5 1 /2 7 2 1 /8 5
/8 9
/16 3
/4 1 1 /2 1 1 /16 1
/2
KH-1363-0-13A LSA 1 25 50.80 85.7 44.4 69.8 139.7 177.8 54.0 15.9 14.3 19.0 38.1 27.0 12.7 GSWE100HHS 3.50
1 1 /16
1 1 /8
KH-1364-0-10A LSA 1 3 /16 2 3 19 /32 1 29 /32 3 3 /16 5 1 /2 7 2 1 /8
11
/16 5
/8
13
/16 1 3 /4 1 3 /16 1
/2 GSWE103HHS 4.25
30 50.80 91.3 48.4 81.0 139.7 177.8 54.0 17.5 15.9 20.6 44.4 30.2 12.7
KH-1365-0-10A LSA 1 1 /4 GSWE104HHS
1 5 /16
1 3 /8 2 3 /8 4 3 /8 2 1 /64 4 6 1 /4 8 1 /4 2 5 7 3
/8 /8 /4 1 1 /4 2 3 /16 1 9 5
/32 /8 GSWE107HHS 7.25
KH-1365-0-13A LSA 1 7 /16 35 60.33 111.1 51.2 101.6 158.8 209.6 66.7 22.2 19.0 31.8 54.0 32.5 15.9
KH-1366-0-10A LSA 1 1 /2 2 3 /8 4 3 /8 2 7 /32 4 6 5 /8 8 1 /4 2 3 3 3 7
/8 /4 /4 /8 2 3 /8 1 3 5
/8 /8 GSWE108HHS 6.75
1 9 /16 40 60.33 111.1 56.4 101.6 168.3 209.6 60.3 19.0 19.0 22.2 60.3 34.9 15.9
KH-1367-0-11A LSA 1 5 /8 2 3 /8 4 1 /2 2 7 /32 4 1 /4 6 5 /8 8 1 /4 2 3 /8
13
/16 3
/4
15
/16 2 1 /2 1 3 /8 5
/8 GSWE111HHS
KH-1367-0-12A LSA 1 11 /16 60.33 114.3 56.4 108.0 168.3 209.6 60.3 20.6 19.0 23.8 63.5 34.9 15.9 GSWE112HHS 7.00
1 3 /4 45
1 13 /16 2 3 /4 5 1 /8 2 15 /32 4 3 /4 8 1 /4 10 5 /8 2 3 /4 1 1 /32 3
/4 1 3 /8 2 3 /4 1 1 /2 5
/8
KH-1368-0-12A LSA 1 7 /8 69.85 130.2 62.7 120.6 209.6 269.9 69.8 26.2 19.0 34.9 69.8 38.1 15.9 GSWE115HHS 11.00
1 15 /16 50
2
2 1 /16 3 1 /8 5 19 /32 2 13 /16 4 15 /16 9 11 3 /8 3 1 /8 1 3
/4 1 5 /16 3 1 23 /32 5
/8
KH-1369-0-13A LSA 2 1 /8 79.38 142.1 71.4 125.4 228.6 288.9 79.4 25.4 19.0 33.3 76.2 43.7 15.9 GSWE203HHS 13.50
2 3 /16 55
2 1 /16
2 3 1 /8 5 7 /8 3 1 /16 5 1 /2 9 11 3 /8 3 1 /8 1 1 /8 7
/8 1 1 /8 3 5 /16 1 27 /32 3
/4
2 79.38 149.2 77.8 139.7 228.6 288.9 79.4 28.6 22.2 28.6 84.1 46.8 19.0 GSWE207HHS 15.50
KH-1370-0-13A LSA 2 60
Recommended shaft tolerances: 1 /2 ” - 1 15 /16", nominal to – .0005", – .013 mm; 2” - 2 15 /16", nominal to – .0010", – .025 mm