Single Pillow Block - Heavy Series - Houston Bearing and Supply

KETCHIE-HOUSTON, INC. PAGE 54
Four Bolt Flange - Standard Series
Replaces Fafnir TCJ
This Ketchie-Houston standard series four
bolt flange unit is supplied completely
assembled and is mounted by means of
bolts through the flange.
These units use a standard series wide
inner ring bearing with an eccentric locking
collar and a one piece Triple-Lip Seal for
better seal performance.
TO ORDER, SPECIFY KETCHIE-HOUSTON OR COMPETITOR’S PART NUMBER
Ketchie Replaces Shaft A B C D E F G H J K Bearing Approx.
Houston Fafnir Diam. Number Unit
Wt.
in. in. in. in in. in. in. in. in. in. in. lbs.
mm mm mm mm mm mm mm mm mm mm
KH-4219-13A TCJ 1 3 3 / 4 2 3 / 4 1
/ 2 1 3 / 16 1 13 / 16
29
/ 64 5
/ 8 1 1 / 16 2 9 / 16 1 1 / 2 GSWE100TTS
95.2 69.8 12.7 30.2 42.9 11.5 15.9 27.0 65.1 38.1 2.25
KH-4220-11A 1 1 / 8 4 1 / 4 3 1 / 4
17
/ 32 1 9 / 32 1 31 / 32
29
/ 64
11
/ 16 1 3 / 16 3 1 3 / 4 GSWE102TTS
KH-4220-12A TCJ 1 3 / 16 107.9 82.6 13.5 32.5 46.8 11.5 17.5 30.2 76.2 44.4 GSWE103TTS
KH-4220-13A 1 1 / 4S GSWE103TTS3 3.00
KH-4221-10A TCJ 1 1 / 4 4 5 / 8 3 5 / 8
17
/ 32 1 11 / 32 1 3 / 32
33
/ 64 3
/ 4 1 9 / 32 3 1 / 2 2 3 / 16 GSWE104TTS
KH-4221-12A TCJ 1 3 / 8 117.5 92.1 13.5 34.1 50.0 13.1 19.0 32.5 88.9 55.6 GSWE106TTS
KH-4221-13A TCJ 1 7 / 16 GSWE107TTS 4.25
KH-4222-10A TCJ 1 1 / 2 5 1 / 8 4 9
/ 16 1 1 / 2 2 5 / 16
33
/ 64
13
/ 16 1 3 / 8 3 7 / 8 2 3 / 8 GSWE108TTS
130.2 101.6 14.3 38.1 56.4 13.1 20.6 34.9 98.4 60.3 5.25
KH-4223-11A TCJ 1 11 / 16 5 3 / 8 4 1 / 8 9
/ 16 1 17 / 32 2 5 / 16
33
/ 64
25
/ 32 1 3 / 8 4 1 / 8 2 1 / 2 GSWE111TTS
KH-4223-12A TCJ 1 3 / 4 136.5 104.8 14.3 38.9 58.7 13.1 19.8 34.9 104.8 63.5 GSWE112TTS 6.00
KH-4224-12A TCJ 1 15 / 16 5 5 / 8 4 3 / 8 9
/ 16 1 11 / 16 2 19 / 32
43
/ 64
29
/ 32 1 1 / 2 4 7 / 16 2 3 / 4 GSWE115TTS
142.9 111.1 14.3 42.9 60.3 17.1 23.0 38.1 112.7 69.8 6.75
KH-4225-10A TCJ 2 6 3 / 8 5 1 / 8
21
/ 32 1 27 / 32 2 15 / 16
43
/ 64 1 3 / 32 1 23 / 32 4 3 / 4 3 GSWE200TTS
KH-4225-13A TCJ 2 3 / 16 161.9 130.2 16.7 46.8 64.7 17.1 27.8 43.7 120.6 76.2 GSWE203TTS 8.75
Recommended shaft tolerances: 1 /2 ” - 1 15 /16", nominal to – .0005", – .013 mm;
2” - 2 15 /16", nominal to – .0010", – .025 mm