Single Pillow Block - Heavy Series - Houston Bearing and Supply

KETCHIE-HOUSTON, INC. PAGE 96
Insert Bearings - Heavy Series - High Temperature - GHWE-HHS
Used in the Following Units:
• KH-2100-0 thru KH-2110-0 (LCJO Type)
• KH-2300-0 thru KH2308-0 (LAO Type)
• KH-2320-0 thru KH-2331-0 (LSAO Type)
Features:
• Wide Inner Ring
• High Temperature - High Speed Integral Seal Arrangements
• High Temperature Grease to 425˚F.
• Alignable Spherical Outside Diameter
• Eccentric Locking Collar
• Relubrication Holes in Outer Ring
Replaces Fafnir GN-KLLB
TO ORDER, SPECIFY KETCHIE-HOUSTON OR COMPETITOR’S PART NUMBER
Ketchie Replaces Bore (1) O.D Ring Width Approx.
Houston Fafnir A B C D E F G H J K S Unit
Inner Outer Wt.
in. in. in. in in. in. in. in. in. in. in.
mm mm mm mm mm mm mm mm mm mm
GHWE102HHS GN102KLLB 1 1 / 8 2.8346 11 / 16 3
/ 4 5 / 32 1 15 / 16
11
/ 16 .142 1 31 / 32 1 7 / 16 .7874 1.50
GHWE103HHS GN103KLLB 1 3 / 16 72 17.46 19.05 3.9 49.21 17.46 3.61 1.97 36.51 20
GHWE104HHS GN104KLLB 1 1 / 4 3.1496
23
/ 32
25
/ 32 5
/ 32 2 3 / 16
11
/ 16 .156 2 1 / 32 1 1 / 2 .8661
GHWE106HHS GN106KLLB 1 3 / 8 80 18.26 19.84 3.9 55.56 17.46 3.96 51.59 38.1 22 1.75
GHWE107HHS GN107KLLB 1 3 / 16
GHWE108HHS GN108KLLB 1 1 / 2 3.5433
25
/ 32
27
/ 32 3
/ 16 2 1 / 2
13
/ 16 .182 2 1 / 4 1 5 / 8 .9843 2.75
90 19.84 21.43 4.76 63.5 20.64 4.62 57.15 41.28 25
GHWE111HHS GN111KLLB 1 11 / 16 3.9370
25
/ 32
29
/ 32 3
/ 16 2 3 / 4
13
/ 16 .189 2 5 / 16 1 11 / 16 1.0630
GHWE112HHS GN112KLLB 1 3 / 4 100 19.84 23.02 4.76 69.85 20.64 4.80 58.74 42.86 27 3.75
GHWE115HHS GN115KLLB 1 15 / 16 4.3307
31
/ 32
31
/ 32 3
/ 16 3 7
/ 8 .203 2 5 / 8 1 31 / 32 1.1417
110 24.61 24.61 4.76 76.2 22.23 5.16 66.68 1.94 29 4.50
GHWE203HHS GN203KLLB 2 3 / 16 4.7244 1 3 / 32 1 5 / 32 3
/ 16 3 1 / 4 7
/ 8 .216 2 7 / 8 2 3 / 16 1.2205
120 1.09 29.37 4.76 82.55 22.23 5.49 73.02 55.56 31 5.50
GHWE207HHS GN207KLLB 2 7 / 16 5.1181 1 7 / 32 1 7 / 32 1
/ 4 3 1 / 2
15
/ 16 .230 3 1 / 8 2 7 / 16 1.2992
130 30.96 30.96 6.35 88.90 23.81 5.84 79.38 61.91 33 6.50
GHWE211HHS GN211KLLB 2 11 / 16 5.9055 1 11 / 32 1 11 / 32 1
/ 4 4 1 1 / 16 .265 3 1 / 2 2 11 / 16 1.4567
150 34.13 34.13 6.35 101.6 26.99 6.73 88.90 68.26 37 10.25
GHWE215HHS GN215KLLB 2 15 / 16 6.2992 1 15 / 32 1 15 / 32 1
/ 4 4 7 / 16 1 1 / 4 .255 3 15 / 16 2 15 / 16 1.5354
160 37.31 37.31 6.35 112.71 31.75 6.48 100.01 74.61 39 12.75
(1)
Bore Tolerance: 1 1 /8” - 1 15 /16", nominal to +.0005”, .013 mm
2 7 /16" - 2 15 /16", nominal to +.0006”, .015 mm
Recommended shaft tolerances: 1 1 /8 ” - 1 15 /16", nominal to – .0005", – .013 mm;
2” - 2 15 /16", nominal to – .0010", – .025 mm