Single Pillow Block - Heavy Series - Houston Bearing and Supply

PAGE 23
Pillow Block - Standard Series
Low Base to Center Height
Replaces Fafnir TAK
KETCHIE-HOUSTON, INC.
This Ketchie-Houston standard series
pillow block features a lower base to
center height dimension.
These units use a standard series, wide
inner ring bearing with an eccentric
locking collar and a one piece Triple-Lip
Seal for better seal performance.
TO ORDER, SPECIFY KETCHIE-HOUSTON OR COMPETITOR’S PART NUMBER
Ketchie Replaces Shaft A B C D E F G H J K N S Bolt Bearing Approx.
Houston Fafnir Diam. Size Number Unit
Wt.
in. in. in. in in. in. in. in. in. in. in. in. in. in. lbs.
mm mm mm mm mm mm mm mm mm mm mm mm mm
1 5 / 16 2 23 /32 1 3 / 4 4 1 / 8 5 1 / 2 1 13 / 32 1
/ 2 7
/ 16
13
/ 16 1 1 / 16 1 1 / 16
45
/ 64 3
/ 8 2.00
KH-4402-13A TAK 1 33.34 68.3 44.4 104.8 139.7 35.7 11.9 11.1 20.6 38.1 27.0 17.9 10 GSWE100TTS
KH-4403-11A TAK 1 1 / 8 1 9 / 16 3 3 / 16 1 29 / 32 4 5 / 8 6 3 / 16 1 3 / 4 9
/ 16 9
/ 16
15
/ 16 1 47 / 64 1 3 / 16 7
/ 8 1
/ 2 GSWE102TTS 3.00
KH-4403-12A TAK 1 3 / 16 39.69 80.2 48.4 117.5 157.2 39.7 13.5 14.3 23.8 44.1 30.2 19.9 12 GSWE103TTS
KH-4403-13A 1 1 / 4S GSWE103TTS3
KH-4404-10A TAK 1 1 / 4 GSWE104TTS
1 13 / 16 3 21 / 32 2 1 / 64 5 6 3 / 4 1 7 / 8
11
/ 16 9
/ 16 7
/ 8 2 7 / 64 1 9 / 32
15
/ 16 1
/ 2 4.00
KH-4404-12A TAK 1 3 / 8 46.04 92.1 51.2 130.2 166.7 45.2 16.7 14.3 24.6 54.0 32.5 22.7 12 GSWE106TTS
KH-4404-13A TAK 1 7 / 16 GSWE107TTS
KH-4405-10A TAK 1 1 / 2 1 15 / 16 3 15 / 16 2 7 / 32 5 3 / 8 7 1 / 8 1 15 / 16 3
/ 4 9
/ 16 1 2 23 / 64 1 3 / 8
31
/ 32 1
/ 2 GSWE108TTS
49.21 100.0 56.4 136.5 179.4 47.6 19.0 14.3 26.2 60.3 34.9 23.8 12 5.00
KH-4406-11A TAK 1 11 / 16 2 1 / 16 4 5 / 32 2 7 / 32 5 21 / 38 7 3 / 8 2
23
/32 9
/ 16
29
/32 2 31 / 64 1 3 / 8 1 1
/ 2 GSWE111TTS 5.50
KH-4406-12A TAK 1 3 / 4 52.39 104.8 56.4 149.2 191.3 50.8 17.5 14.3 28.6 63.5 34.9 25.4 12 GSWE112TTS
2 3 / 16 4 15 / 32 2 15 / 32 6 3 / 16 8 2 3 23
/ 16 /32
11
/ 16
15
/ 16 2 47 / 64 1 1 / 2 1 3 / 32 5
/ 8 6.75
KH-4407-12A TAK 1 15 / 16 55.56 112.7 62.7 158.0 200.0 55.6 17.5 17.5 23.8 69.8 38.1 27.8 16 GSWE115TTS
KH-4408-10A TAK 2 GSWE200TTS
2 7 / 16 4 29 / 32 2 13 / 16 6 15 / 16 8 12 / 16 2 5 / 16 3
/ 4
11
/ 16 1 1 / 8 2 63 / 64 1 23 / 32 1 5 / 32 5
/ 8 8.75
61.91 124.6 71.4 176.2 222.3 58.7 19.0 18.3 29.4 76.2 43.7 29.4 16
KH-4408-13A TAK 2 3 / 16 GSWE203TTS
Recommended shaft tolerances: 1 / 2 ” - 1 15 /16", nominal to – .0005", – .013 mm;
2” - 2 15 /16", nominal to – .0010", – .025 mm