Single Pillow Block - Heavy Series - Houston Bearing and Supply

PAGE 69
KETCHIE-HOUSTON, INC.
Take-up Units - Standard Series with Triple Lip Sealed Inserts
The Ketchie-Houston standard series
take-up units are used where shaft
adjustment and belt tightening devices
are required, as on conveyor
applications.
These units use a standard series, wide
inner ring bearing with an eccentric
locking collar and a one piece Triple-Lip
seal for better seal performance
TO ORDER, SPECIFY KETCHIE-HOUSTON OR COMPETITOR'S PART NUMBER
Ketchie Shaft A B C S D E R H K J F G P L M N Bearing Approx.
Houston Diam. Number Unit
Wt.
in. in. in. in in. in. in. in. in. in. in. in. in. in. in. in. in. lbs.
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
KH-4422-13A 1 1 15 /16 7
/8 1 1 /16 1 15 /32
17
/32 1 3 /4 2 21 /32 2 1 /4 3
/4 1 1 /4 1
/2 5
/8 1 3 /8 2 1 /4 3 3 5 /8 GSWE100TTS 3.50
49.2 22.2 27.0 37.3 13.5 44.4 67.5 57.2 19.0 31.8 12.7 15.9 34.9 57.2 76.2 92.1
KH-4423-11A 1 1 /8 GSWE102TTS
KH-4423-12A 1 3 /16 2 3 /16 1 1 3 /16 1 1 /2
17
/32 2 2 27 /32 2 7 /16 7
/8 1 7 /16 1
/2 5
/8 1 5 /8 2 1 /2 3 1 /2 4 1 /8 GSWE103TTS 4.50
KH-4423-13A 1 1 /4S 55.6 25.4 30.2 38.1 13.5 50.8 72.2 61.9 22.2 36.5 12.7 15.9 41.3 63.5 88.9 104.8 GSWE103TTS3
KH-4424-10A 1 1 /4 GSWE104TTS
KH-4424-12A 1 3 /8 2 9 /32 1 1 9 /32 1 7 /16
17
/32 2 2 15 /16 2 1 /2 5
/8 1 7 /16 1
/2 5
/8 1 15 /16 2 3 /4 3 1 /2 4 1 /8 GSWE106TTS 4.75
KH-4424-13A 1 7 /16 57.9 25.4 32.5 36.5 13.5 50.8 74.6 63.5 22.2 36.5 12.7 15.9 49.2 69.8 88.9 104.8 GSWE107TTS
KH-4425-10A 1 1 /2 2 21 /32 1 9 /32 1 3 /8 1 3 /4
11
/16 2 9 /16 3 15 /32 3 1 /4 1 1 /8 1 15 /16 5
/8 3
/4 2 3 /32 3 1 /4 3 31 /32 4 3 /4 GSWE108TTS 7.50
67.5 32.5 34.9 44.4 17.5 65.1 88.1 82.6 28.6 49.2 15.9 19.0 53.3 82.6 100.8 120.6
KH-4426-12A 1 3 /4 2 21 /32 1 9 /32 1 3 /8 1 3 /4
11
/16 2 9 /16 3 15 /32 3 1 /4 1 1 /8 1 15 /16 5
/8 3
/4 2 3 /32 3 1 /4 3 31 /32 4 3 /4 GSWE112TTS 7.25
67.5 32.5 34.9 44.4 17.5 65.1 88.1 82.6 28.6 49.2 15.9 19.0 53.3 82.6 100.8 120.6
KH-4427-12A 1 15 /16 2 25 /32 1 9 /32 1 1 /2 1 15 /16
11
/16 2 9 /16 3 3 3 /4 1 1 /8 1 15 /16 5
/8 3
/4 2 11 /32 3 3 /8 3 31 /32 4 3 /4 GSWE115TTS 8.25
70.6 32.5 38.1 49.2 17.5 65.1 91.3 82.6 28.6 49.2 15.9 19.0 59.5 85.7 100.8 120.6
KH-4428-10A 2 3 1 /32 1 3 /8 1 23 /32 2 3 /16 1 1 /16 2 3 /4 4 23 /32 4 1 3 /8 2 1 /2 3
/4 1 1 /4 2 23 /32 4 5 3 /32 5 7 /8 GSWE200TTS
KH-4428-13A 2 3 /16 77.0 34.9 43.7 55.6 27.0 69.8 119.9 101.6 34.9 63.5 19.0 31.8 69.1 101.6 129.4 149.2 GSWE203TTS 14.25
Recommended shaft tolerances: 1 - 1 15 /16", nominal to – .0005", – .013 mm
2" - 2 15 /16", nominal to – .0010", – .025 mm