MT3000 Complete - Electric - MaxFlight Corporation

More documents

Recommendations

Info

Mechanical power requirements: The pitch movement is powered by a 5 HP electric motor. The roll movement is powered by a 3.0 HP electric motor. The lift movement is powered by a 3 HP electric motor. Static information: Height:7’ 9” (approx.) Width: 12’ 8” (approx.) Length: 15’ (approx.) Weight: 4800 lbs. Dynamic information: Height:12’ 10” (approx.) Width: 12’ 8” (approx.) Length: 15’ (approx.) Weight: 5300 lbs. maximum Fastener schedule: Refer to the MaxFlight MT3000 Installation Manual Maximum static load distribution per footing: NS – based on static weight distributed by (4) 8” x 16” feet and (2) 4” x 14” feet INA = Information Not Available N/A = Not Applicable UNK = Unknown NS = Not Specified 1-5 Ride Restrictions There are certain conditions that the machines should not be operated under. These conditions are described below. 1-5A Intoxication If a patron is under the influence of any drugs or alcohol they should not be allowed to utilize the equipment. If a question arises have a manager speak to the patron. 1-5B Heart Conditions Any heart or other similar condition would preclude a passenger from riding the simulator. 1-5C Pregnancy It is not recommended that women who are pregnant ride the simulator. 1-5D Weight and Height Restrictions The patrons must be at least 48” (1.22 m) tall and total weight is not to exceed 500 lb. (226.8 kg) with no more than a 100 lb. (45.36 kg) difference between the passengers. All patrons must be capable of sitting normally in the seat and be capable of using all the restraint devices available and mandatory. If this is not possible the patron cannot ride. 1-5E Impairments We recommend that patrons with the following impairments/conditions do not ride the VR2002 Cyber Coaster: ♦ Head, neck, heart or back problems
♦ Recent operations ♦ High blood pressure ♦ Motion sickness ♦ Women who are pregnant ♦ Epileptic patrons; due to the special strobe and lighting effects that are known to trigger seizures ♦ Intoxicated patrons ♦ Claustrophobia 1-6 Safety Due to the nature of the MT3000 there are several safety precautions that must be observed in order to ensure the safety of both the patrons and the operators during operation of the experience. 1-6A Ensure that the cockpit has completed movement prior to continuing with any other procedures. 1-6B NOTE: Ensure that during the time of operation, all persons must stay clear of the simulator in order to prevent injuries. 1-6C Ensure that the operating personnel do not operate the simulator with any of the cover plates removed. 1-6D Ensure that only authorized personnel open the power distribution box for any reason. 1-6E Ensure that patrons pass the height and weight requirements to ride the simulator. 1-6F Queue Line Safety The queue line must be kept orderly. The patrons must remain behind the established barriers while waiting their turn to ride. The queue line should also be used to familiarize patrons with the operation of the Occupant Panic Switch (OPS) Button. 1-6G Loading/Unloading Safety During the loading and unloading of patrons, the operator must ensure that the simulator has come to a complete stop prior to opening the cockpit. The operator is required to assist the patrons to negotiate the steps and cockpit. 1-6H During the operation of the simulator, the operator must stay within the proximity of their assigned units. Operators must watch for such things as equipment failure, abuse of the simulator and customers who wish to terminate game play. 1-6I During the operation of the ride, the operator(s) should be posted at the control console where the computer screen, mouse and unit will be in his/her direct line of sight
Page 1 and 2: MaxFlight MT3000(B) “ELECTRIC”
Page 3 and 4: Introduction Page 17 Emergency Proc
Page 5 and 6: Current Software window Regedit32 w
Page 7 and 8: DET-011 Tail Closure/Pitch Motor Pa
Page 9: CHAPTER 1 - INTRODUCTION 1-1 Introd
Page 13 and 14: 2-2A Description of Control Windows
Page 15 and 16: Game Setup window opens, select ISL
Page 17 and 18: (Fig. 4) to help find home level in
Page 19 and 20: performed by qualified personnel, f
Page 21 and 22: NEW EMERGENCY RAISE PROCEDURES FOR
Page 23 and 24: Date of Inspection: MaxFlight Corpo
Page 25 and 26: 11 - Electrical Configurations U.S.
Page 27 and 28: CHAPTER 1 - THEORY OF OPERATION 1-1
Page 29 and 30: 1-2M Encoders All encoders (three)
Page 31 and 32: 1-5D Pitch and Roll Roll/Pitch CPU
Page 33 and 34: CHAPTER 2 - ELECTRICAL SYSTEM 2-1 E
Page 35 and 36: c. Install Microsoft Management Con
Page 37 and 38: NOTE: When you apply power to the i
Page 39 and 40: 2-6B Removal of the Front Cover The
Page 41 and 42: 1. Power up the inverter. 2. Connec
Page 43 and 44: 5. All the legends at the top will
Page 45 and 46: NO OTHER PARAMETERS SHOULD BE DIFFE
Page 47 and 48: A machined steel part. Transmits ro
Page 49 and 50: xiii. Using an inclinometer, set it
Page 51 and 52: . NOTE! As the projector ages, some
Page 53 and 54: Motion Platform Window Lift control
Page 55 and 56: Status Window Computer Serial DEVIC
Page 57 and 58: USER JOYSTICK 0 (AXES) Calibration
Page 59 and 60: Path Game log and alert log routing
Page 61 and 62:
Lock To prevent inadvertent tamperi
Page 63 and 64:
New Motion Test Client window Allow
Page 65 and 66:
Lift Motion Editor Settings Counter
Page 67 and 68:
Pitch Motion Filter 1 Editor Pitch
Page 69 and 70:
Roll Motion Filter 2 Editor Roll Mo
Page 71 and 72:
5-2 Weekly Maintenance and Lubricat
Page 73 and 74:
4) Appearance, external cracks, dis
Page 75 and 76:
5-8C Test Image but “NO” Other
Page 77 and 78:
NOTE! Command movement of the motor
Page 79 and 80:
5-20 Setup and Calibration of Joyst
Page 81 and 82:
Verify that the Maxflight I/O Syste
Page 83:
4.) Appearance, external cracks, di
Page 86 and 87:
MaxFlight Corporation 750 Airport R
Page 88 and 89:
P-26 Analog cable to interface pane
Page 90 and 91:
ELECTRICAL CIRCUITS LIST SE11-001 P
Page 92 and 93:
. Menu Color to BLUE c. Language to
Page 94 and 95:
CHAPTER 1 - SET UP The first thing
Page 96 and 97:
onto the pitch shaft. Position pitc
Page 98:
43. Pull out E-Stop on side of cont
Page 117 and 118:
Check the pine tree fasteners in th
Page 119 and 120:
Visually inspect for slip, trip and
Page 121:
B. Mechanical
show all

MT3000 Complete - Electric - MaxFlight Corporation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?