MT3000 Complete - Electric - MaxFlight Corporation

More documents

Recommendations

Info

5-21 Creating and configuring the Artificial Intel. (AI) Joystick Devices Page 81 CHAPTER 6: Time Replacement Items 6-1 Introduction Page 82 6-2 Relays Page 84 6-3 Projector Bulbs Page 84 6-4 Non Destructive Testing Procedures Page 84 Attachment. 1Weekly Inspection Checklist Page 87 2 Cable Numbering and Routing Page 88 3 Electrical Circuits List Page 91 4 Hitachi Projector Settings Page 92 Part of Document Package I: Mitsubishi Transistorized Inverter Manual II: Hitachi Projector Manual III: Sumitomo Motor and Gear Box Manual IV: Warranty Cards for all Items Section III: Installation Page 94 TABLE OF CONTENTS INSTALL CHAPTER 1: SET UP 1-1 Field Torque Procedure (Turn-of-the-Nut) Page 95 1-2 Assembly Instructions Page 95 ASSEMBLY DRAWINGS (SEE ”DRAWINGS FILE” ) DET-01 Power Box Page 100 DET-02A Right side Electrical Page 100 DET-02B Left Side Electrical Page 101 DET-04 Encoder Placement Page 101 DET-05 Platform Front Support Page 102 DET-06 Floor Plan\Accessories Page 102 DET-07 TV and Cabinetry Page 103 DET-08 Squaring the Ride Page 103 DET-09 Cabinetry Page 104 DET-010 Tail Cover and Stand Page 104
DET-011 Tail Closure/Pitch Motor Page 105 DET-013 Platform/Front Stand Page 105 DET-014 A frame Assy. Page 106 DET-015 Side A frame ABS Page 106 DET-016 Pitch shaft placement Page 107 DET-017 Pitch shaft Installation Page 107 DET-018 Safety Wiring Page 108 DET-022 Power Box Serial Interface Page 108 DET-035 CPU Card Layout Page 109 DET-036 CPU Card Layout MT,FS Page 109 DET-037 Mother Board Layout Page 110 DET-038 Lube Requirements Page 110 DET-039 MT Layout and spacing Page 111 DET-040 Lower Cockpit Fiberglass Page 111 DET-041 Lower ear ABS Page 112 DET-042 Upper rear ABS Page 112 DET-043A Lift Jack Clutch/Tower Page 113 DET-044 Pitch Rings Installation Page 113 DET-045 Roll Hub and Gear Box Page 114 DET-046 Cockpit Power Strip Page 114 DET-048 Lift cross drive system Page 115 DET-049 Cable routing to center Page 115 DET-050 Motion Control Card Jumpers settings Page 116 DET-051 MT,FS Command Console Layout Page 116 APPENDIX B: INSTALLATION & PERFORMANCE TESTING CHECKLIST Page 117 Section IV: Drawings Start at Page 122 A. Electrical B. Mechanical
Page 1 and 2: MaxFlight MT3000(B) “ELECTRIC”
Page 3 and 4: Introduction Page 17 Emergency Proc
Page 5: Current Software window Regedit32 w
Page 9 and 10: CHAPTER 1 - INTRODUCTION 1-1 Introd
Page 11 and 12: ♦ Recent operations ♦ High bloo
Page 13 and 14: 2-2A Description of Control Windows
Page 15 and 16: Game Setup window opens, select ISL
Page 17 and 18: (Fig. 4) to help find home level in
Page 19 and 20: performed by qualified personnel, f
Page 21 and 22: NEW EMERGENCY RAISE PROCEDURES FOR
Page 23 and 24: Date of Inspection: MaxFlight Corpo
Page 25 and 26: 11 - Electrical Configurations U.S.
Page 27 and 28: CHAPTER 1 - THEORY OF OPERATION 1-1
Page 29 and 30: 1-2M Encoders All encoders (three)
Page 31 and 32: 1-5D Pitch and Roll Roll/Pitch CPU
Page 33 and 34: CHAPTER 2 - ELECTRICAL SYSTEM 2-1 E
Page 35 and 36: c. Install Microsoft Management Con
Page 37 and 38: NOTE: When you apply power to the i
Page 39 and 40: 2-6B Removal of the Front Cover The
Page 41 and 42: 1. Power up the inverter. 2. Connec
Page 43 and 44: 5. All the legends at the top will
Page 45 and 46: NO OTHER PARAMETERS SHOULD BE DIFFE
Page 47 and 48: A machined steel part. Transmits ro
Page 49 and 50: xiii. Using an inclinometer, set it
Page 51 and 52: . NOTE! As the projector ages, some
Page 53 and 54: Motion Platform Window Lift control
Page 55 and 56: Status Window Computer Serial DEVIC
Page 57 and 58:
USER JOYSTICK 0 (AXES) Calibration
Page 59 and 60:
Path Game log and alert log routing
Page 61 and 62:
Lock To prevent inadvertent tamperi
Page 63 and 64:
New Motion Test Client window Allow
Page 65 and 66:
Lift Motion Editor Settings Counter
Page 67 and 68:
Pitch Motion Filter 1 Editor Pitch
Page 69 and 70:
Roll Motion Filter 2 Editor Roll Mo
Page 71 and 72:
5-2 Weekly Maintenance and Lubricat
Page 73 and 74:
4) Appearance, external cracks, dis
Page 75 and 76:
5-8C Test Image but “NO” Other
Page 77 and 78:
NOTE! Command movement of the motor
Page 79 and 80:
5-20 Setup and Calibration of Joyst
Page 81 and 82:
Verify that the Maxflight I/O Syste
Page 83:
4.) Appearance, external cracks, di
Page 86 and 87:
MaxFlight Corporation 750 Airport R
Page 88 and 89:
P-26 Analog cable to interface pane
Page 90 and 91:
ELECTRICAL CIRCUITS LIST SE11-001 P
Page 92 and 93:
. Menu Color to BLUE c. Language to
Page 94 and 95:
CHAPTER 1 - SET UP The first thing
Page 96 and 97:
onto the pitch shaft. Position pitc
Page 98:
43. Pull out E-Stop on side of cont
Page 117 and 118:
Check the pine tree fasteners in th
Page 119 and 120:
Visually inspect for slip, trip and
Page 121:
B. Mechanical
show all

MT3000 Complete - Electric - MaxFlight Corporation

Create successful ePaper yourself

Delete template?

Save as template?