920i Installation manual - Rice Lake Weighing Systems

More documents

Recommendations

Info

SCALES Menu, FORMAT Submenu, SPLIT = OFF Parameter Choices Description DECPNT 8888888 8888880 8888800 8.888888 88.88888 888.8888 8888.888 88888.88 888888.8 DSPDIV 1D 2D 5D MULT 1.0 0.000001– 9999999 UNITS SEC MIN HOUR INTERVL 10 1–100 REFRESH 0.1 0.1–60 Decimal point location. Determines the location of the decimal point or dummy zeros in the display. Display divisions. Selects the minimum division size for the ROC units displayed weight. Multiplier. Specifies the conversion factor by which the primary units are multiplied by to obtain the displayed rate of change units. See Section 11.10 on page 128 for information about conversion factors. Rate-of-change units. Update interval. Specifies the number of refreshes over which the rate-of-change is calculated. For example, with REFRESH set to 0.1 second and INTERVL at 60, each weight value takes 6 seconds (0.1 * 60) to be flushed from the ROC data. Refresh interval. Specifies the number of seconds between rate-of-change samples. Table 3-3. SCALES Menu, FORMAT Submenu Parameters, SPLIT = OFF (Continued) 34 <strong>920i</strong> <strong>Installation</strong> Manual
… GRADS SPLIT FORMAT ZTRKBND ZRANGE MOTBAND … DECPT1 DDIV1 MAX1 DECPT2 DDIV2 MAX2 8888888 8888880 8888800 8.888888 88.88888 888.8888 8888.888 88888.88 888888.8 1D 2D 5D 50.00000 weight 888888.8 8888888 8888880 8888800 8.888888 88.88888 888.8888 8888.888 88888.88 2D 5D 1D 50.00000 weight DECPT3 DDIV3 MAX3 UNITS 888888.8 8888888 8888880 8888800 8.888888 88.88888 888.8888 8888.888 88888.88 5D 50.00000 1D weight 2D If SPLIT = 3RNG or 3INTVL LB KG G OZ TN T GN TROYOZ TROYLB LT CUSTOM OFF NONE Figure 3-6. SCALES Menu, FORMAT Submenu, SPLIT OFF Configuration 35
Page 1: ® Programmable HMI Indicator/Contr
Page 4 and 5: 3.2.9 VERS Menu . . . . . . . . . .
Page 6 and 7: iv 920i Installation Manual
Page 8 and 9: Option Cards The CPU board provides
Page 10 and 11: Select Scale Diagnostics Alibi Cont
Page 12 and 13: Option Cards Table 1-5 lists the av
Page 14 and 15: emote display with keypad for truck
Page 16 and 17: 2.0 Installation This section descr
Page 18 and 19: 2.3.4 Serial Communications The fou
Page 20 and 21: J5 OPTION CARD CONNECTOR J6 OPTION
Page 22 and 23: 1 SLOT 1 2.5 Expansion Board Config
Page 24 and 25: 2.8 Fuse Replacement Fuses for the
Page 26 and 27: 2.11 Replacement Parts and Assembly
Page 28 and 29: 22 920i Installation Manual Figure
Page 30 and 31: 3.0 Configuration To configure the
Page 32 and 33: 3.2 Menu Structures and Parameter D
Page 34 and 35: SCALES Menu Parameter Choices Descr
Page 36 and 37: SCALES Menu Parameter Choices Descr
Page 38 and 39: SCALES Menu, FORMAT Submenu, SPLIT
Page 42 and 43: SCALES Menu, FORMAT Submenu, SPLIT
Page 44 and 45: 3.2.2 SERIAL Menu See Section 11.6
Page 46 and 47: SCALES SERIAL FEATURE PFORMT SETPTS
Page 48 and 49: SERIAL Menu Parameter Choices Descr
Page 50 and 51: SERIAL Menu Parameter Choices Descr
Page 52 and 53: FEATURE Menu Parameter Choices Desc
Page 54 and 55: FEATURE Menu Parameter Choices Desc
Page 56 and 57: FEATURE Menu, REGULAT/INDUST Submen
Page 58 and 59: 3.2.5 SETPTS Menu See Section 9.0 o
Page 60 and 61: DIG I/O Menu Parameter Choices Desc
Page 62 and 63: ALGOUT Menu Parameter Choices Descr
Page 64 and 65: 4.0 iRev Calibration The 920i can b
Page 66 and 67: 4.3 Serial Command Calibration To c
Page 68 and 69: 5.0 Using iRev The iRev 4 utility p
Page 70 and 71: 5.6 Connecting to the Indicator Con
Page 72 and 73: 6.2 Connecting a USB Device The 920
Page 74 and 75: 6.6 Saving Configuration Files and
Page 76 and 77: Command Description Supported Ticke
Page 78 and 79: Format Default Format String Used W
Page 80 and 81: • To add a character: position th
Page 82 and 83: The truck register can be printed t
Page 84 and 85: Kind Description Batch Continuous -
Page 86 and 87: 9.2 Setpoint Menu Parameters Figure
Page 88 and 89: B +REL -REL %REL RESREL Same as +RE
Page 90 and 91:
D COZ, INMOTON, INRANGE, and BATCHP
Page 92 and 93:
F DELTA VALUE SOURCE CLRACCM CLRTAR
Page 94 and 95:
H ALWAYS NEVER BRANCH 0 1-100 DINCN
Page 96 and 97:
SETPTS Menu Level 4 submenus VALUE
Page 98 and 99:
SETPTS Menu ACCESS ON HIDE OFF Spec
Page 100 and 101:
To begin a batch process, turn the
Page 102 and 103:
10.0 Serial Commands The 920i indic
Page 104 and 105:
Command Description Values SC.SRC#n
Page 106 and 107:
Command Description Values EDP.INPU
Page 108 and 109:
Command Description Values CONTACT.
Page 110 and 111:
Command Description Values WDGT#n D
Page 112 and 113:
10.1.6 Normal Mode Commands The nor
Page 114 and 115:
Example. The following commands pla
Page 116 and 117:
creates a visible, 1.5" x 1.5" (120
Page 118 and 119:
Symbol Style (x) Description Widget
Page 120 and 121:
11.0 Appendix 11.1 Troubleshooting
Page 122 and 123:
on page 14). 4. Power up the 920i.
Page 124 and 125:
REGULAT / INDUST Parameter REGULAT
Page 126 and 127:
11.6 Custom Stream Formatting Each
Page 128 and 129:
Format Identifier Defined By Descri
Page 130 and 131:
11.7.2 Cardinal 738 Indicator Sampl
Page 132 and 133:
11.8 Data Formats Continuous Output
Page 134 and 135:
11.10 Conversion Factors for Second
Page 136 and 137:
11.12 Dimension Drawings 12.50" 10.
Page 138 and 139:
10.38" BACK VIEW 11.56" 5.20" 9.16"
Page 140 and 141:
11.13 Printed Information System Ma
Page 142:
920i Limited Warranty Rice Lake Wei
show all

920i Installation manual - Rice Lake Weighing Systems

Create successful ePaper yourself

Delete template?

Save as template?