920i Installation manual - Rice Lake Weighing Systems
920i Installation manual - Rice Lake Weighing Systems
920i Installation manual - Rice Lake Weighing Systems
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
SERIAL Menu<br />
Parameter Choices Description<br />
EOLDLY 0<br />
0–255<br />
HANDSHK<br />
OFF<br />
XONOFF<br />
HRDWAR<br />
INPUT CMD<br />
PROGIN<br />
PORTTYPE 232<br />
485<br />
422<br />
RESPONSE<br />
ON<br />
OFF<br />
End-of-line delay. Sets the delay period, in 0.1-second intervals, from when a formatted line is<br />
terminated to the beginning of the next formatted serial output. Value specified must be in the<br />
range 0-255, in tenths of a second (10 = 1 second).<br />
Specifies whether XON/XOFF flow control characters or hardware handshaking is used.<br />
Hardware handshaking is available only on Port 2.<br />
Determines whether the input will be handled by the core or routed to a user program (if<br />
present)<br />
Specifies whether Port 4 is used for RS-232, RS-485, or RS-422 communications. If 485 is<br />
selected, additional prompts are shown to specify half- or full-duplex operation and RS-485<br />
address.<br />
NOTE: RS-485 communications is compatible with iQUBE 2 . It can be specified for Port 4,<br />
and for odd numbered expansion ports 5 and higher.<br />
Specifies whether the port transmits replies to serial commands.<br />
SFMT format Specifies the stream format used for the streamed data (SCALE or IND SC scale types). The<br />
default format is the Consolidated Controls format (see Section 11.8 on page 126). See<br />
Section 11.6 on page 120 for information about custom stream formatting.<br />
SOURCE source_scale If STREAM is set to a value other than OFF, SOURCE specifies the source scale for data<br />
streamed from the port.<br />
STOP BITS 2<br />
1<br />
Selects number of stop bits transmitted or received by the port.<br />
STREAM<br />
TERMIN<br />
OFF<br />
LFT<br />
INDUST<br />
4KEYS<br />
KEYPAD<br />
DISPLAY<br />
CR/LF<br />
CR<br />
TOKENS PRIMAR<br />
SECNDR<br />
TERTIA<br />
GROSS<br />
INVALID<br />
MOTION<br />
ZERO<br />
NET<br />
OK<br />
RANGE<br />
TARE<br />
Level 4 Submenus<br />
Specifies what data, if any, is streamed from the port.<br />
LFT streams data at the display rate specified by the DSPRATE parameter on the FEATURE<br />
menu (see page 46).<br />
INDUST streams data at the A/D update rate specified by the SMPRATE parameter on the<br />
SCALES menu (see page 29).<br />
4KEYS and KEYPAD stream keypad events to a receiving indicator. KEYPAD transmits all<br />
keypad events; 4KEYS transmits keypresses of the ZERO, GROSS/NET, TARE, and UNITS<br />
keys only.<br />
DISPLAY streams the complete display image to the receiving indicator in local/remote<br />
indicator configurations. See Section 11.5 on page 119 for more information.<br />
NOTE: Streaming is not supported for RS-485 connections.<br />
Termination character. Selects termination character for data sent from the port.<br />
If STREAM is set to LFT or INDUST, the TOKENS parameter can be used to replace tokens<br />
used in the data stream from the indicator front panel. See Section 11.6 on page 120 for more<br />
information about custom stream formatting.<br />
RS-485 Port Information<br />
Table 3-6. Serial Menu Parameters (Continued)<br />
Configuration 43