P-51B Mustang 32e ARF Manual - Horizon Hobby

More documents

Recommendations

Info

6. Use the radio system to center the aileron servo. Place the servo horn on the servo so the longer portion of the arm is parallel to the servo center line. If the horn does not align, rotate the horn 180-degrees, as there are an odd number of splines on the servo output. Use a felt-tipped pen to mark the arm that protrudes through the servo cover. 8. Attach the servo horn to the servo using the screw removed from the servo and a #1 Phillips screwdriver. 10. Remove the tape holding the string located in the wing near the opening for the aileron servo. Tie the string to the end of the aileron servo extension. 7. Remove the servo horn from the servo. Use side cutters to remove the arms from the horn that were not marked in the previous step. Enlarge the hole in the servo horn that is 5/16-inch (7mm) from the center of the horn using a pin vise and 5/64-inch drill bit. 9. Use string or a commercially available connector to secure a 12-inch (305mm) servo extension to the aileron servo lead. 11. Use the string to pull the aileron servo extension through the wing to the opening for the flap servo. When the flap servo is installed, you will use the string to pull both the aileron and flap servo leads to the root of the wing. 20 E-flite P-51B Mustang 32e ARF Assembly Manual
12. Use 2–3 drops of thin CA in each of the holes for the aileron servo cover mounting screws. This will harden the surrounding wood, which helps prevent the screws from breaking the wood and vibrating loose. 14. Insert the Z-bend in the 2-inch (52mm) linkage wire through the hole enlarged in Step 7. 16. Use a hobby knife with a #11 blade to remove the control horn backplate from the control horn. Discard the backplate as it will not be used when installing the control horn. 13. While you have the thin CA in your hand, apply 2–3 drops in each of the holes for the aileron control horn mounting screws. 15. Use four 2mm x 8mm sheet metal screws with shoulder and a #1 Phillips screwdriver to secure the aileron servo cover to the wing. Use the mark made in Step 1 to make sure the cover is oriented correctly. Then remove the mark can using rubbing alcohol and a paper towel. 17. Use a #1 Phillips screwdriver and two 2mm x 8mm sheet metal screws to attach the control horn to the aileron. E-flite P-51B Mustang 32e ARF Assembly Manual 21
Page 1 and 2: P-51B Mustang 32e ARF Assembly Manu
Page 3 and 4: Table of Contents Notice...........
Page 5 and 6: Hinging the Control Surfaces Requir
Page 7 and 8: 12. Remove the control surface and
Page 9 and 10: 2. Slide the pushrod wire into the
Page 11 and 12: 6. Slide the stabilizer tube into t
Page 13 and 14: 5. The canopy is held in position a
Page 15 and 16: 5. Apply a piece of hook and loop t
Page 17 and 18: 15. Slide the rudder pushrod into t
Page 19: Aileron Servo Installation Required
Page 23 and 24: 4. Remove the servo horn from the s
Page 25 and 26: 15. Use four 2mm x 8mm sheet metal
Page 27 and 28: 2. Temporarily attach the axle to t
Page 29 and 30: Required Parts Canopy hatch Radio b
Page 31 and 32: 9. When balancing your model, suppo
Page 33 and 34: 8. Use a #0 Phillips screwdriver to
Page 35 and 36: 6. Apply the tail numbers to the ve
Page 37 and 38: 4. Using the dullcote lacquer - mis
Page 39 and 40: 11. Next work on the exhaust streak
Page 41 and 42: Flying Your P-51B Mustang 32e ARF N
Page 43 and 44: Warranty Services Questions, Assist
Page 45 and 46: 8. Under no circumstances may a pil
Page 47 and 48: Building and Flying Notes E-flite P

P-51B Mustang 32e ARF Manual - Horizon Hobby

Create successful ePaper yourself

Delete template?

Save as template?