wireless monitoring system of gas detector - Faculty of Electrical ...

More documents

Recommendations

Info

xi LIST OF FIGURES FIGURE NO. TITLE PAGE 2.1 The overall system of Carbon Monoxide Detection and Autonomous Countermeasure System for a mill use Wireless sensor and Actuator Network 7 2.2 Design of the sensor location 8 2.3 Result of the gas concentration based on the sensor replacement 9 2.6 Gas sensor working principle 11 2.7 Zigbee module 12 2.8 LabVIEW icon image 13 2.9 Arduino board 15 2.10 Buzzer model 16 2.11 LEDs images 17 2.12 Exhaust Fan Images 18
xii 3.1 Methodology of the Project 20 3.2 Block Circuit Diagram 21 3.3 Experiment Diagram of the Project 22 3.4 Circuit Diagram for Gas Detector 22 3.5 MQ3 and MQ6 image 23 3.6 Gas Sensor Circuit Diagram 24 3.7 The Gas Sensor Connection to Arduino Pins. 25 3.8 Output Circuit Diagram 26 3.9 Relay Connection Circuit Diagram 27 3.10 Zigbee Output Connection Circuit 28 3.11 Voltage Output of Gas Sensor Versus Reading of Bits in Arduino. 3.12 Resistance Ratio versus Concentration Gas for MQ9 3.13 Flow chart for the Arduino Programming for MQ9 30 32 36 3.14 Arduino input and output port initialization 37 3.15 Declaration of the pin 38 3.16 Programming process in Arduino 40 3.17 Zigbee receiver Connection to USB Port 40 3.18 Test the COM Of Each Zigbee 41
Page 1 and 2: WIRELESS GAS MONITORING SYSTEM OF G
Page 3 and 4: “I hereby declare that I have rea
Page 5 and 6: ii I declare that this thesis entit
Page 7 and 8: iv ACKNOWLEDGEMENT In preparing thi
Page 9 and 10: vi ABSTRAK Tujuan projek ini adalah
Page 11 and 12: viii 2.1 Introduction 6 2.2 The Haz
Page 13: x LIST OF TABLES TABLE NO. TITLE PA
Page 17 and 18: xiv LIST OF SYMBOLS CO - Carbon Mon
Page 19 and 20: xvi LIST OF APPENDICES APPENDIX TIT
Page 21 and 22: 2 min, and death within 30 min. Ver
Page 23 and 24: 4 iv. Zigbee Arduino Uno is a devic
Page 25 and 26: 6 CHAPTER 2 LITERATURE REVIEW 2.1 I
Page 27 and 28: 8 (which is 300ppm), the actuator c
Page 29 and 30: 10 2.2 The hazardous gases Based on
Page 31 and 32: 12 From Ohms Law in equation 2.1, v
Page 33 and 34: 14 advanced analysis and data visua
Page 35 and 36: 16 2.5.1 Buzzer Figure 2.10: Buzzer
Page 37 and 38: 18 2.5.3 Exhaust Fan Exhaust fan as
Page 39 and 40: 20 Start Writing programming and co
Page 41 and 42: 22 Figure 3.3: Experiment Diagram o
Page 43 and 44: 24 Figure 3.6: Gas Sensor Circuit D
Page 45 and 46: 26 Table 3.1: Threshold Value for G
Page 47 and 48: 28 Last but not least, the output c
Page 49 and 50: 30 As mention in chapter 2, Arduino
Page 51 and 52: 32 iii. Step 3: (200, 2) (1000, 1)
Page 53 and 54: 34 iv. Step 4: Since Arduino only r
Page 55 and 56: 36 start read the output voltage by
Page 57 and 58: 38 void setup() { Serial.begin(9600
Page 59 and 60: 3.3V RX TX 5V GND 40 digitalWrite(l
Page 61 and 62: 42 The set up for the Zigbe data tr
Page 63 and 64: 44 Figure 3.23: VISA Interfacing Bl
Page 65 and 66:
46 The last stage in the data monit
Page 67 and 68:
48 Figure 3.28: Step 2 Then, the fi
Page 69 and 70:
50 CHAPTER 4 RESULT AND DISCUSSION
Page 71 and 72:
52 The overall project set up shown
Page 73 and 74:
54 After that, the system of gas mo
Page 75 and 76:
56 CHAPTER 5 CONCLUSION AND RECOMME
Page 77 and 78:
58 REFERENCES [1] Incorporated, C.
Page 79 and 80:
60 APPENDIX 1. Block diagram for MQ
Page 81 and 82:
3. Arduino programming for MQ3 62
show all

wireless monitoring system of gas detector - Faculty of Electrical ...

Create successful ePaper yourself

Delete template?

Save as template?