wireless monitoring system of gas detector - Faculty of Electrical ...

More documents

Recommendations

Info

51 processes analog to digital converter (ADC) from 0 to 1024 which are in 10 bits. Voltage output from the gas sensor (0-5)V will be read as (0-1024) decimal output in Arduino. Furthermore, this system will enable data transfer in LABVIEW by wireless using zigbee device and complete with the alarm system. 4.3 Project Result Figure 4.1 show the output result of the alarm system when Arduino threshold in the warning mode. Yellow LED and exhaust fan will be turn on as the initially system set up in order to control the air quality in the building. Yellow LED means warning in the system. Figure 4.1: Alarm indicator of the project.
52 The overall project set up shown in the Figure 4.2. the system are divided into two part. First part is on the alarm system. The second part is on the software system which is monitoring system. Figure 4.2: Overall Project Configuration An experimented was carried out using two type of gas sensor with two different kinds of gasses. The first experiment was done with MQ9 gas sensor. This sensor detects the concentration of the LPG gas. The result for monitoring system of MQ9 gas sensor is shown in the Figure 4.3 below. The second experiment is to detect the level of concentration alcohol gas by using MQ3 gas sensor. Figure 4.4 shows the outcome result for second gas sensor, MQ3.
Page 1 and 2:
WIRELESS GAS MONITORING SYSTEM OF G
Page 3 and 4:
“I hereby declare that I have rea
Page 5 and 6:
ii I declare that this thesis entit
Page 7 and 8:
iv ACKNOWLEDGEMENT In preparing thi
Page 9 and 10:
vi ABSTRAK Tujuan projek ini adalah
Page 11 and 12:
viii 2.1 Introduction 6 2.2 The Haz
Page 13 and 14:
x LIST OF TABLES TABLE NO. TITLE PA
Page 15 and 16:
xii 3.1 Methodology of the Project
Page 17 and 18:
xiv LIST OF SYMBOLS CO - Carbon Mon
Page 19 and 20: xvi LIST OF APPENDICES APPENDIX TIT
Page 21 and 22: 2 min, and death within 30 min. Ver
Page 23 and 24: 4 iv. Zigbee Arduino Uno is a devic
Page 25 and 26: 6 CHAPTER 2 LITERATURE REVIEW 2.1 I
Page 27 and 28: 8 (which is 300ppm), the actuator c
Page 29 and 30: 10 2.2 The hazardous gases Based on
Page 31 and 32: 12 From Ohms Law in equation 2.1, v
Page 33 and 34: 14 advanced analysis and data visua
Page 35 and 36: 16 2.5.1 Buzzer Figure 2.10: Buzzer
Page 37 and 38: 18 2.5.3 Exhaust Fan Exhaust fan as
Page 39 and 40: 20 Start Writing programming and co
Page 41 and 42: 22 Figure 3.3: Experiment Diagram o
Page 43 and 44: 24 Figure 3.6: Gas Sensor Circuit D
Page 45 and 46: 26 Table 3.1: Threshold Value for G
Page 47 and 48: 28 Last but not least, the output c
Page 49 and 50: 30 As mention in chapter 2, Arduino
Page 51 and 52: 32 iii. Step 3: (200, 2) (1000, 1)
Page 53 and 54: 34 iv. Step 4: Since Arduino only r
Page 55 and 56: 36 start read the output voltage by
Page 57 and 58: 38 void setup() { Serial.begin(9600
Page 59 and 60: 3.3V RX TX 5V GND 40 digitalWrite(l
Page 61 and 62: 42 The set up for the Zigbe data tr
Page 63 and 64: 44 Figure 3.23: VISA Interfacing Bl
Page 65 and 66: 46 The last stage in the data monit
Page 67 and 68: 48 Figure 3.28: Step 2 Then, the fi
Page 69: 50 CHAPTER 4 RESULT AND DISCUSSION
Page 73 and 74: 54 After that, the system of gas mo
Page 75 and 76: 56 CHAPTER 5 CONCLUSION AND RECOMME
Page 77 and 78: 58 REFERENCES [1] Incorporated, C.
Page 79 and 80: 60 APPENDIX 1. Block diagram for MQ
Page 81 and 82: 3. Arduino programming for MQ3 62
show all

wireless monitoring system of gas detector - Faculty of Electrical ...

Create successful ePaper yourself

Delete template?

Save as template?