wireless monitoring system of gas detector - Faculty of Electrical ...

More documents

Recommendations

Info

17 2.5.2 LED A light emitting diode (LED) as shown in Figure 2.12 is a semiconductor light source. LED is used as the indicator lamp in the many devices and is increasingly used for lighting. The LED is based on the semiconductor diode. Figure 2.11: LEDs images When a diode is forward biased which is switch on, electron are able to recombine with holes within the devices, releasing energy in the form of photon. This effect is called electroluminescence and the colour of the light is determined by the energy gap of the semiconductor. LED are usually integrated optical components are used to shape its radiation pattern and assist in the reflection.
18 2.5.3 Exhaust Fan Exhaust fan as shown in Figure 2.13 is a fan for ventilating an interior by drawing air from the interior and expelling it outside. This project needs a system combination with exhaust fan as the precaution step before entering the dangerous level. Exhaust fan will suck out all the air inside the room or building that had been installed with the system to the outside of the building. Therefore, the air quality inside the building will maintain in the safe air quality. Figure 2.12: Exhaust fan model
Page 1 and 2: WIRELESS GAS MONITORING SYSTEM OF G
Page 3 and 4: “I hereby declare that I have rea
Page 5 and 6: ii I declare that this thesis entit
Page 7 and 8: iv ACKNOWLEDGEMENT In preparing thi
Page 9 and 10: vi ABSTRAK Tujuan projek ini adalah
Page 11 and 12: viii 2.1 Introduction 6 2.2 The Haz
Page 13 and 14: x LIST OF TABLES TABLE NO. TITLE PA
Page 15 and 16: xii 3.1 Methodology of the Project
Page 17 and 18: xiv LIST OF SYMBOLS CO - Carbon Mon
Page 19 and 20: xvi LIST OF APPENDICES APPENDIX TIT
Page 21 and 22: 2 min, and death within 30 min. Ver
Page 23 and 24: 4 iv. Zigbee Arduino Uno is a devic
Page 25 and 26: 6 CHAPTER 2 LITERATURE REVIEW 2.1 I
Page 27 and 28: 8 (which is 300ppm), the actuator c
Page 29 and 30: 10 2.2 The hazardous gases Based on
Page 31 and 32: 12 From Ohms Law in equation 2.1, v
Page 33 and 34: 14 advanced analysis and data visua
Page 35: 16 2.5.1 Buzzer Figure 2.10: Buzzer
Page 39 and 40: 20 Start Writing programming and co
Page 41 and 42: 22 Figure 3.3: Experiment Diagram o
Page 43 and 44: 24 Figure 3.6: Gas Sensor Circuit D
Page 45 and 46: 26 Table 3.1: Threshold Value for G
Page 47 and 48: 28 Last but not least, the output c
Page 49 and 50: 30 As mention in chapter 2, Arduino
Page 51 and 52: 32 iii. Step 3: (200, 2) (1000, 1)
Page 53 and 54: 34 iv. Step 4: Since Arduino only r
Page 55 and 56: 36 start read the output voltage by
Page 57 and 58: 38 void setup() { Serial.begin(9600
Page 59 and 60: 3.3V RX TX 5V GND 40 digitalWrite(l
Page 61 and 62: 42 The set up for the Zigbe data tr
Page 63 and 64: 44 Figure 3.23: VISA Interfacing Bl
Page 65 and 66: 46 The last stage in the data monit
Page 67 and 68: 48 Figure 3.28: Step 2 Then, the fi
Page 69 and 70: 50 CHAPTER 4 RESULT AND DISCUSSION
Page 71 and 72: 52 The overall project set up shown
Page 73 and 74: 54 After that, the system of gas mo
Page 75 and 76: 56 CHAPTER 5 CONCLUSION AND RECOMME
Page 77 and 78: 58 REFERENCES [1] Incorporated, C.
Page 79 and 80: 60 APPENDIX 1. Block diagram for MQ
Page 81 and 82: 3. Arduino programming for MQ3 62

wireless monitoring system of gas detector - Faculty of Electrical ...

Create successful ePaper yourself

Delete template?

Save as template?