Perkins Motor Operation and Maintenance Manual (English) - REED

More documents

Recommendations

Info

78 SEBU8325-01 Maintenance Section Water Pump - Inspect • Inspect the lubrication system for leaks at the front crankshaft seal, the rear crankshaft seal, the oil pan, the oil filters and the rocker cover. • Inspect the fuel system for leaks. Look for loose fuel line clamps and/or tie-wraps. • Inspect the piping for the air intake system and the elbows for cracks and for loose clamps. Ensure that hoses and tubes are not contacting other hoses, tubes, wiring harnesses, etc. Note: The water pump seal is lubricated by the coolant in the cooling system. It is normal for a small amount of leakage to occur as the engine cools down and parts contract. Visually inspect the water pump for leaks. Renew the water pump seal or the water pump if there is an excessive leakage of coolant. Refer to the Disassembly and Assembly Manual, “Water Pump - Remove and Install” for the disassembly and assembly procedure. • Inspect the alternator belts and any accessory drive belts for cracks, breaks or other damage. Belts for multiple groove pulleys must be replaced as matched sets. If only one belt is replaced, the belt will carry more load than the belts that are not replaced. The older belts are stretched. The additional load on the new belt could cause the belt to break. • Drain the water and the sediment from the fuel tank on a daily basis in order to ensure that only clean fuel enters the fuel system. • Inspect the wiring and the wiring harnesses for loose connections and for worn wires or frayed wires. • Inspect the ground strap for a good connection and for good condition. • Disconnect any battery chargers that are not protected against the current drain of the starting motor. Check the condition and the electrolyte level of the batteries, unless the engine is equipped with amaintenance free battery. • Check the condition of the gauges. Replace any gauges that are cracked. Replace any gauge that can not be calibrated. Water Pump - Inspect i01907756 A failed water pump may cause severe engine overheating problems that could result in the following conditions: • Cracks in the cylinder head • Apistonseizure • Other potential damage to the engine
SEBU8325-01 79 Warranty Section Warranty Information Warranty Section Warranty Information Emissions Warranty Information i02676009 This engine may be certified to comply with exhaust emission standards and gaseous emission standards that are prescribed by the law at the time of manufacture, and this engine may be covered by an Emissions Warranty. Consult your authorized Perkins dealer or your authorized Perkins distributor in order to determine if your engine is emissions certified and if your engine is subject to an Emissions Warranty.
Page 1 and 2:
SEBU8325-01 July 2012 Operation and
Page 3 and 4:
SEBU8325-01 3 Table of Contents Tab
Page 5 and 6:
SEBU8325-01 5 Safety Section Safety
Page 7 and 8:
SEBU8325-01 7 Safety Section Genera
Page 9 and 10:
SEBU8325-01 9 Safety Section Fire P
Page 11 and 12:
SEBU8325-01 11 Safety Section Engin
Page 13 and 14:
SEBU8325-01 13 Product Information
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
SEBU8325-01 21 Operation Section Li
Page 23 and 24:
SEBU8325-01 23 Operation Section Fe
Page 25 and 26:
SEBU8325-01 25 Operation Section En
Page 27 and 28: SEBU8325-01 27 Operation Section En
Page 29 and 30: SEBU8325-01 29 Operation Section Co
Page 31 and 32: SEBU8325-01 31 Operation Section Co
Page 33 and 34: SEBU8325-01 33 Maintenance Section
Page 77: SEBU8325-01 77 Maintenance Section
Page 81 and 82: SEBU8325-01 81 Index Section Forewo
Page 83 and 84: Product and Dealer Information Note
show all

Perkins Motor Operation and Maintenance Manual (English) - REED

Create successful ePaper yourself

Delete template?

Save as template?