Download - National Rejectors Inc. GmbH

More documents

Recommendations

Info

SAFETY INSTRUCTIONS G-13.mft MDB/S1 2 Safety instructions Before operating the device for the first time, please read through these instructions carefully at least once, and most importantly the safety instructions. This is to ensure you have understood the contents of these instructions as well as how to operate the coin validator. Proper use Series G-13.mft coin validators with MDB or S1 interface are intended to be used in amusement, vending and service machines with an MDB or S1 interface and are supposed to check the coins inserted in the machines for specific coin properties. These coin validators have been constructed in compliance with the state of the art and recognized safety regulations. Nevertheless this equipment can be a source of danger. Therefore please observe the following safety regulations. 10 National Rejectors, Inc. GmbH, Buxtehude
G-13.mft MDB/S1 SAFETY INSTRUCTIONS Protecting yourself and equipment The coin validator may only be connected by a qualified electrician. Only use the coin validator according to proper use. Under no circumstances can the manufacturer be held liable for any damage or loss resulting from improper use of the device. The coin validator PCB is fitted with components which may be damaged beyond repair by electrostatic discharge. Please observe the handling instructions for components exposed to the risk of electrostatic discharge. Pull out the vending machine’s mains plug before you install, clean or remove the coin validator. Select the correct voltage for the coin validator (see label). Ensure the correct potential equalization in the vending machine. Never pull the connecting cable of the coin validator from the vending machine when a voltage is applied. Contact NRI if you wish to alter the construction of the device to a greater extent than that described in these instructions. Keep water and other liquids away from the coin validator. If the device is no longer required, please dispose of it correctly. We reserve the right to make technical modifications to the device which are not covered by these instructions. National Rejectors, Inc. GmbH, Buxtehude 11
Page 1: Technical Documentation Electronic
Page 4 and 5: TABLE OF CONTENTS G-13.mft MDB/S1 4
Page 7 and 8: G-13.mft MDB/S1 INTRODUCTION 1 Gene
Page 9: G-13.mft MDB/S1 INTRODUCTION Advant
Page 13 and 14: G-13.mft MDB/S1 DESIGN 1 5 MINI 2 3
Page 15 and 16: G-13.mft MDB/S1 DESIGN Switch assig
Page 17 and 18: G-13.mft MDB/S1 DESIGN Interface -
Page 19 and 20: G-13.mft MDB/S1 FUNCTION 4 Function
Page 21 and 22: G-13.mft MDB/S1 FUNCTION Single or
Page 23 and 24: G-13.mft MDB/S1 FUNCTION Sorting wi
Page 25 and 26: G-13.mft MDB/S1 STARTING UP 5 Start
Page 27 and 28: G-13.mft MDB/S1 STARTING UP Device
Page 29 and 30: G-13.mft MDB/S1 STARTING UP 4 6 5 7
Page 31 and 32: G-13.mft MDB/S1 OPERATION 6 Operati
Page 33 and 34: G-13.mft MDB/S1 OPERATION ... with
Page 35 and 36: G-13.mft MDB/S1 OPERATION Teach mod
Page 37 and 38: G-13.mft MDB/S1 OPERATION To save w
Page 39 and 40: G-13.mft MDB/S1 MAINTENANCE AND SER
Page 41 and 42: G-13.mft MDB/S1 TECHNICAL DATA 9 Te
Page 43 and 44: G-13.mft MDB/S1 TECHNICAL DATA Nati
Page 45 and 46: G-13.mft MDB/S1 TECHNICAL DATA Nati
Page 47 and 48: G-13.mft MDB/S1 TECHNICAL DATA Comm
Page 49 and 50: G-13.mft MDB/S1 TECHNICAL DATA Acce
Page 51 and 52: G-13.mft MDB/S1 TECHNICAL DATA Conf
Page 53 and 54: G-13.mft MDB/S1 INDEX E ECV 56 Elec
Page 55 and 56: G-13.mft MDB/S1 GLOSSARY Glossary A
Page 57: G-13.mft MDB/S1 GLOSSARY Switching

Download - National Rejectors Inc. GmbH

Create successful ePaper yourself

Delete template?

Save as template?