Sentry II - Truth Hardware

More documents

Recommendations

Info

30 Did you find what you’re looking for? The Truth Hardware Web site is a great resource for the latest product and installation information. It’s available at www.truth.com
Regulatory Compliance United States of America Federal Communications Commission (FCC) Unintentional emitter per FCC Part 15 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: o Reorient or relocate the receiving antenna. o Increase the separation between the equipment and receiver. o Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. o Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by Truth Hardware could void the FCC compliance and negate your authority to operate the product. FCC Declaration of Conformity According to 47 CFR, Parts 15.107 and 15.109 Class B Responsible party: Truth Hardware, 700 West Bridge St., Owatonna, MN 55060 www.truth.com or 1-800-324-4487 Product: Sentry II Hand Held Remote (43.53) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including interferences that may cause undesired operation. Canada Industry Canada (IC) Unintentional emitter per ICES-003 This class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Europe European Community EMC Directive (CE) Compliance with these directives implies conformity to the following European Norms or Regulations: Emissions Immunity ETSI EN 300-220-1 v1.3.1 (2000-09) ETSI EN 301 489-3 v1.2.1 (2000-08) ETSI EN 300-220-3 v1.1.1 (2000-09) EN 55014-2: 1997 ETSI EN 301 489-3 v1.2.1 (2000-08) EN 55014-1: 1997 CONFORMS TO ANSI/UL STD 325; CERTIFIED TO CAN/CSA STD C22.2 NO. 68 Did you find what you’re looking for? The Truth Hardware Web site is a great resource for the latest product and installation information. It’s available at www.truth.com 31
Page 1 and 2: An FKI Industries Company 700 West
Page 3 and 4: Table of Contents [ Preparation Get
Page 5 and 6: Getting Started Item Part Number 1.
Page 7 and 8: Main wiring diagram Did you find wh
Page 9 and 10: 3. Install the Control Box DANGER:
Page 11 and 12: 6. Install Screen Interlock! DANGER
Page 13 and 14: 9. Install Cover • Remove the cen
Page 15 and 16: Status Light Indicator During opera
Page 17 and 18: Wall Mounted Switch Panel (Optional
Page 19 and 20: High Priority Inputs (HPI) The cont
Page 21 and 22: Control unit setup for Power Blind
Page 23 and 24: DIP Switch Settings The DIP switche
Page 25 and 26: Total System Reset: If the operatio
Page 27 and 28: Service Obtaining Service Truth Har
Page 29: Synchronous Operation Please Note:

Sentry II - Truth Hardware

Create successful ePaper yourself

Delete template?

Save as template?