User Manual

More documents

Recommendations

Info

2DBench Tutorial For this example, you can use the default parameters to drill holes or patterns; however, if you want to change them, activate the parameters dialog, enter new values and click [Accept New Values] then [Close]. Select pattern drilling. Place the cursor on the left side of the screen for the location of the first hole (row 1, hole 1) and [click]. Set the direction of the front row - move the cursor to the right. The bearing of the row is shown on the status bar. [Click] to set the direction. Set the burden direction by moving the cursor below the front row line and [click]. The blast pattern is created on the screen. (The same technique can be used to set the pattern from the back row – note the [Burden Direction] in the parameters.) 66 JKSimBlast
2DBench Tutorial Press [End] to centre the blast on the screen. Place the cursor near any hole in the pattern, and [click] the query toolbar button [?] to show information on the hole. Move the cursor to display a different hole. Single holes and nodes can be placed anywhere in the blast by placing the cursor and [click]. Nodes have the same Bench Level as blast holes. NOTE: by default, drilled holes are Unmarked and imported holes are Marked. Saving t he blast It is advisable to save the blast regularly. Blasts are saved in a MS Access database. One database can hold multiple blasts. Save the Blast Select >File > Save Blast in the menu. JKSimBlast 67
Page 1:
last simulation evaluation and mana
Page 4 and 5:
Disclaimer JKSimBlast is a suite of
Page 6 and 7:
Contents Introduction .............
Page 8 and 9:
Sample Blasts......................
Page 10 and 11:
2DFace ............................
Page 12 and 13:
Calculation Region.................
Page 15 and 16:
Introduction Overview JKSimBlast co
Page 17 and 18:
Introduction Equipment Requirements
Page 19 and 20:
Introduction 1. Start the installat
Page 21 and 22:
4. Customer Information Introductio
Page 23 and 24:
6. Setup Type Select the type of in
Page 25 and 26:
Introduction Select how and when to
Page 27 and 28:
8. Ready to install Introduction Th
Page 29 and 30: Introduction Fast Program Start The
Page 31 and 32: JKBMS Overview The Blast Management
Page 33 and 34: JKBMS Data Structure The BMS uses h
Page 35 and 36: JKBMS When a BMS database is opened
Page 37 and 38: JKBMS Function Toolbar Function Too
Page 39 and 40: JKBMS To add a node, first select t
Page 41 and 42: JKBMS The 3D Viewer can display any
Page 43 and 44: JKBMS Always try to run JKSimBlast
Page 45 and 46: Miscellaneous JKBMS The Misc. tab c
Page 47 and 48: JKBMS To empty the Recycle Bin, [ri
Page 49 and 50: JKBMS databases. The data is provid
Page 51 and 52: JKBMS Both report options operate i
Page 53 and 54: JKBMS JKSimBlast 39
Page 55 and 56: JKBMS Tutorial Setup This tutorial
Page 57 and 58: JKBMS Tutorial Add Object To add ob
Page 59 and 60: JKBMS Tutorial such as a site (and
Page 61 and 62: JKBMS Tutorial Add Blast from 2DBen
Page 63 and 64: JKBMS Tutorial Select the blasts to
Page 65 and 66: JKBMS Tutorial [Right-click] the bl
Page 67 and 68: JKBMS Tutorial The blast will open
Page 69 and 70: JKBMS Tutorial JKSimBlast 55
Page 71 and 72: 2DBench Overview 2DBench is a graph
Page 73 and 74: 2DBench Design Modes A blast is div
Page 75 and 76: 2DBench in the centre of the hole.
Page 77 and 78: 2DBench JKSimBlast 63
Page 79: 2DBench Tutorial Creating a Blast D
Page 83 and 84: 2DBench Tutorial This mode is for d
Page 85 and 86: 2DBench Tutorial >File >Save Blast
Page 87 and 88: 2DBench Tutorial On the [Delay]
Page 89 and 90: 2DBench Tutorial Open the paramete
Page 91 and 92: 2DBench Tutorial Open the par
Page 93 and 94: 2DBench Tutorial To run the sim
Page 95 and 96: 2DBench Tutorial JKSimBlast 81
Page 97 and 98: 2DRing General Functions 2DRing inc
Page 99 and 100: 2DRing Title Bar Menu Bar Tool Bar
Page 101 and 102: 2DRing Table 1.1 Change options dia
Page 103 and 104: 2DRing The Object colour option all
Page 105 and 106: 2DRing Global Construction Tools Se
Page 107 and 108: 2DRing The user may also change the
Page 109 and 110: 2DRing Figure 1.9 View of marked an
Page 111 and 112: 2DRing Figure 1.10 Design Informati
Page 113 and 114: 2DRing Loading & Saving Designs can
Page 115 and 116: 2DRing Importing and Exporting 2DRi
Page 117 and 118: 2DRing The user should also specify
Page 119 and 120: 2DRing Once the appropriate informa
Page 121 and 122: 2DRing The above reports are column
Page 123 and 124: 2DRing paper). A logo and a comment
Page 125 and 126: 2DRing Design Input Within 2DRing,
Page 127 and 128: 2DRing Figure 2.2 Edit ring planes
Page 129 and 130: 2DRing Multiple line segment drawin
Page 131 and 132:
2DRing Drill Drives and Drill posit
Page 133 and 134:
2DRing a) Ah = 1 b) Ar = W/2 c) Ar
Page 135 and 136:
2DRing Individual holes can be posi
Page 137 and 138:
2DRing Selection and Loading of Exp
Page 139 and 140:
2DRing Selection and Loading of Del
Page 141 and 142:
2DRing The surface delay mode allow
Page 143 and 144:
2DRing Figure 3.1 Detonation simula
Page 145 and 146:
2DRing e L 2 1 P 187. 5 D h 2
Page 147 and 148:
2DRing Weighting 1 Time of referenc
Page 149 and 150:
2DRing Figure 3.4 shows the 3D expl
Page 151 and 152:
2DRing Fragmentation A review of br
Page 153 and 154:
2DRing selection of fragmentation
Page 155 and 156:
2DRing In the Rock Structure tab, t
Page 157 and 158:
2DRing JKSimBlast 143
Page 159 and 160:
2DFace General Functions 2DFace inc
Page 161 and 162:
2DFace Title Bar Menu Bar Tool Bar
Page 163 and 164:
2DFace Table 1.1 Change options dia
Page 165 and 166:
2DFace The Object colour option all
Page 167 and 168:
2DFace Figure 1.5 Move 2D cursor to
Page 169 and 170:
2DFace Figure 1.7 New scale option
Page 171 and 172:
2DFace Query Options Two functions
Page 173 and 174:
2DFace Figure 1.10 Design summary i
Page 175 and 176:
2DFace Figure 1.12 Save Design and
Page 177 and 178:
2DFace Figure 1.14 Import data dial
Page 179 and 180:
2DFace Figure 1.17 String closure d
Page 181 and 182:
2DFace The configuration for a part
Page 183 and 184:
2DFace The user must select the pri
Page 185 and 186:
2DFace Design Input Within 2DFace,
Page 187 and 188:
2DFace Figure 2.1 String In line an
Page 189 and 190:
2DFace position of the new drive. T
Page 191 and 192:
2DFace Figure 2.4 Defining sections
Page 193 and 194:
2DFace As shown in Figure 2.5 four
Page 195 and 196:
2DFace . Figure 2.7 Burn cut select
Page 197 and 198:
2DFace 2. Select the multiple holes
Page 199 and 200:
2DFace 2. Select the multiple holes
Page 201 and 202:
2DFace Selection and Loading of Exp
Page 203 and 204:
2DFace Selection & Loading of Delay
Page 205 and 206:
2DFace Delay accessories are stored
Page 207 and 208:
2DFace 6. Definition of drill holes
Page 209 and 210:
2DFace Figure 3.3 Output of a digit
Page 211 and 212:
2DFace Equation (6) can be integrat
Page 213 and 214:
2DFace 11.Select type of calculatio
Page 215 and 216:
2DFace Detonation Simulation and Ti
Page 217 and 218:
2DFace Figure 3.8 Detonation simula
Page 219 and 220:
2DFace JKSimBlast 205
Page 221 and 222:
2DView Overview 2DView is an extend
Page 223 and 224:
2DView Opening a Blast Opening a bl
Page 225 and 226:
2DView When the list is complete, c
Page 227 and 228:
2DView Choose View Several pre-defi
Page 229 and 230:
2DView Scroll Bars The display can
Page 231 and 232:
2DView use the mouse or GoTo (or [H
Page 233 and 234:
Margin 2DView This sets an extra ma
Page 235 and 236:
2DView the speed of calculation. Wh
Page 237 and 238:
2DView [click] or press [Enter] aga
Page 239 and 240:
2DView [Move All Points] : apply a
Page 241 and 242:
2DView open cut mine after removal
Page 243 and 244:
Regions 2DView Calculate for only t
Page 245 and 246:
Choosing Results 2DView This step i
Page 247 and 248:
2DView rock mass. After this time i
Page 249 and 250:
2DView calculate the contours, the
Page 251 and 252:
2DView Actual Downhole Connection L
Page 253 and 254:
2DView line contours, only the mini
Page 255 and 256:
2DView 2. Open the Extra Hole Data
Page 257 and 258:
TimeHEx Overview TimeHEx (Time vs H
Page 259 and 260:
TimeHEx Set the time interval for t
Page 261 and 262:
TimeHEx delays. The data in the tex
Page 263 and 264:
TimeHEx Toggle the visibility of gr
show all

User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?