SENSORS

MAGNETIC / HALLLinear Hall ICMelexis’ programmable linear Hall sensors are ideal for position and fuel level sensing applications. The analog output isproportional to the applied flux density and the transfer characteristic can be programmed to any specific requirement.MelexisPartNumberOutput VoltageRange (V)Sensitivity(mV/mT)Magnetic Field Range(mT)Supply Voltage(V)Supply Current(mA)OperatingTemp. (°C)*PackageMLX90215 0 to 5 5 to 140 4.5 to 5.5 E, L VA (SIP4)MLX90251-0 0 to 5 2.6 to 15 333 to 800 4.5 to 5.5 2.5 to 6.5 E, L VA, TSSOPMLX90251-1 0 to 5 10 to 35 156 to 333 4.5 to 5.5 2.5 to 6.5 E, L VA, TSSOPMLX90251-2 0 to 5 18 to 90 62 to 156 4.5 to 5.5 2.5 to 6.5 E, L VA, TSSOPMLX90251-3 0 to 5 50 to 210 6 to 62 4.5 to 5.5 2.5 to 6.5 E, L VA, TSSOPMLX90288 0 to 5 N/A 6 to 650 4.5 to 5.5 8.8 to 10 L SOIC-8MLX90291 PWM N/A ±15 to ±400 4.5 to 5.5 8 to 10 L SOIC-8PWM / PAS4 /MLX90292N/A ±30 to ±170 4.6 - 8.7 13 - 19 G TSSOP16PSI5-A*note: E: -40 to +85, G:-40 to +125, L:-40 to +150Magnetic Pattern Recognition SensorThe magnetic pattern recognition sensor consists of a pair of magnetoresistive (MR) elements and a magnet. When a materialprinted with magnetic ink is scanned over the sensor, the magnetic flux applied to MRs changes, causing change of outputvoltages.MAGNETIC / HALLMurataPart NumberDetection Width(mm)Resolution(mm)Supply Voltage(V)Total Resistance Max.(ohm)Output VoltageMin.Output VoltageMax.Operating Temp.(°C)BS05M1KFFA 10mm 0.75mm 5V 3k 100mV p-p – 0 to 50BS05N1HFAA 3mm 0.75mm 5V 4k 400mV rms – -20 to 60BS05N1NFAA 6mm 0.87mm 5V 6k 330mV rms – -20 to 60BS05M1KFCB 10mm x 6ch 0.75mm 5V 10k 50mV ems – 0 to 50BS05M1KFJA 10.3mm x18ch 0.75mm 5V 3k 100mV p-p – 0 to 50BS05M1KFKA 10.3mm 0.75mm 5V 10k 50mV rms – 0 to 50BS05P1PGAB 1.5mm x1ch 0.75mm 5.25 6k 220mV rms 320mV rms -20 to 60BS05T1HGLC 3mm x1ch 0.75mm 5 3k 220mV rms 400mV rms -20 to 60Current SensorThe contact-less current sensor consists of a CMOS Hall effect sensor with a thin ferromagnetic layer structured on itssurface. The integrated ferromagnetic (IMC) layer is used as a magnetic flux concentrator providing a high magnetic gainwhich significantly increases the signal to noise ratio of the sensor. The sensor is particularly appropriate for DC and/or ACcurrent measurements up to 90kHz with ohmic isolation, very low insertion loss, fast response time, small package size andlow assembly cost requirements.50MelexisPart Number Output Types Bandwidth (kHz)Magnetic FieldRange (mT)Supply Voltage(V)Supply Current(mA)Operating Temp.(°C)PackageMLX91205 Voltage DC - 100 kHz ±10 / ±25 4.5 to 5.5 10 -40 to 125 SOIC-8MLX91206 Voltage / PWM DC - 90 kHz ±10 / ±25 4.5 to 5.5 9 -40 to 125 SOIC-8MLX91207 Voltage DC - 60 kHz ±15 to ±400 4.5 to 5.5 9 -40 to 125 SOIC-8www.FutureElectronics.com/Sensors