Summit - Denver Instrument

More documents

Recommendations

Info

NOTE: This equipment has beentested and found to comply withthe limits pursuant to part 15 of FCCRules. These limits are designed toprovide reasonable protectionagainst harmful interference. Thisequipment generates, uses and canradiate radio frequency energy and, ifnot installed and used in accordancewith these instructions, may causeharmful interference to radio communications.For information on the specific limitsand class of this equipment, pleaserefer to the Declaration of Conformity.Depending on the particular class,you are either required or requestedto correct the interference.If you have a Class A digital device,you need to comply with the FCCstatement as follows: “Operation ofthis equipment in a residential area islikely to cause harmful interference inwhich case the user will be requiredto correct the interference at his ownexpense.”If you have a Class B digital device,please read and follow the FCCinformation given below:“However, there is no guarantee thatinterference will not occur in a particularinstallation. If this equipmentdoes cause harmful interference toradio or television reception, whichcan be determined by turning theequipment off and on, the user isencouraged to try to correct the interferenceby one or more of the followingmeasures:– Reorient or relocate the receivingantenna.– Increase the separation betweenthe equipment and receiver.– Connect the equipment into anoutlet on a circuit different fromthat to which the receiver is connected.– Consult the dealer or an experiencedradio/TV technician forhelp.”Before you operate this equipment,check which FCC class (Class A orClass B) it has according to theDeclaration of Conformity included.Be sure to observe the informationof this Declaration.8
Connecting Electronic Peripheral Devices§ Make sure to unplug the balance from ACpower before you connect or disconnect aperipheral device (printer or computer) to orfrom the interface port.Warmup TimeTo ensure accurate results, the balance mustwarm up for 30 minutes before operation.Only after this time will the instrument havereached the required operating temperature.Using Verified Balances in Legal Metrology inthe EU*:$ Make sure to allow the equipment to warmup for at least 24 hours after initial connectionto AC power or after a relatively longpower outage.Operation Outside the Temperature Range!Operating the balance beyond the temperaturerange of +10…+30°C (50°…86°F).Differences from the specifications listed inthe chapter on “Specifications” are possible.* Including the Signatories of the Agreementon the European Economic Area9
Page 1 and 2: SummitElectronic Analytical and Pre
Page 3 and 4: ContentsWarnings and Safety Precaut
Page 5 and 6: Getting StartedStorage and Shipping
Page 7: Connecting the Balance to AC Power/
Page 11 and 12: Leveling the BalancePurpose:- To co
Page 13 and 14: Basic Weighing FunctionPreparation
Page 15 and 16: Calibration and AdjustmentPurposeCa
Page 17 and 18: External CalibrationParameters (cha
Page 19 and 20: Menu NavigationExample: Setting the
Page 21 and 22: Parameter Settings: Overviewο = Fa
Page 23 and 24: Level 1 Level 2 Level 3 Level 4 Men
Page 25 and 26: Input: ID number, Date and TimeLeve
Page 27 and 28: Device InformationLevel 1 Level 2 L
Page 29 and 30: Example : Counting parts of equal w
Page 31 and 32: Example: Determining residual weigh
Page 33 and 34: Example:Calculating the weight per
Page 35 and 36: Example: Determining animal weight
Page 37 and 38: Example: Counting parts into a cont
Page 39 and 40: Example: Totalizing weight valuesPa
Page 41 and 42: Example: Determining the density of
Page 43 and 44: Example: Change display from the ba
Page 45 and 46: ISO/GLP-compliant Printout/RecordFe
Page 47 and 48: Data InterfacePurposeYour balance c
Page 49 and 50: Care and MaintenanceServiceOn reque
Page 51 and 52: OverviewSpecificationsSpecification
Page 53 and 54: Specifications for Individual Model
Page 55 and 56: Verified Models with EC-type Approv
Page 57: C MarkingThe balance complies with
Page 61 and 62:
Warn- und SicherheitshinweiseSicher
Page 63 and 64:
InstallationWaage aufstellenWaagen
Page 65 and 66:
Anschluss von elektronischen Kompon
Page 67 and 68:
Waage nivellierenZweck:- Ausgleich
Page 69 and 70:
Grundfunktion WägenMerkmale- Waage
Page 71 and 72:
JustierenZweckJustieren ist die Tä
Page 73 and 74:
Extern JustierenVoreinstellung:SETU
Page 75 and 76:
Menü-BedienungBeispiel: Sprache ei
Page 77 and 78:
Parametereinstellungen: Übersicht
Page 79 and 80:
Ebene 1 Ebene 2 Ebene3 Ebene 4 Code
Page 81 and 82:
Eingabe: Ident-Nummer, Datum und Uh
Page 83 and 84:
Gerätespezifische InformationenEbe
Page 85 and 86:
Beispiel: Zählen von gleichgewicht
Page 87 and 88:
Beispiel: Restgewichtsbestimmung in
Page 89 and 90:
Beispiel:Berechnung des Flächengew
Page 91 and 92:
Beispiel: Automatisches Wägen von
Page 93 and 94:
Beispiel: Mehrere Komponenten einwi
Page 95 and 96:
Beispiel: Wägewerte summierenVorei
Page 97 and 98:
Beispiel: Dichte eines festen Wäge
Page 99 and 100:
Beispiel: Einheit wechseln von Gram
Page 101 and 102:
ISO/GLP-ProtokollMerkmaleDie Gerät
Page 103 and 104:
DatenschnittstelleZweckDie Waage be
Page 105 and 106:
Pflege und WartungServiceAuf Anford
Page 107 and 108:
ÜbersichtTechnische DatenAllgemein
Page 109 and 110:
Modellspezifische technische DatenM
Page 111 and 112:
Geeichte Modelle mit EG-Bauartzulas
Page 113 and 114:
C - KennzeichnungDas Gerät erfüll
Page 115:
Copyright by Denver Instrument GmbH
show all

Summit - Denver Instrument

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?