S3.15 Strength System Base Owner's Manual - Precor

S3.15Strength-TrainingFitness EquipmentAssembly and Maintenance Guide

S3.15 Assembly and Maintenance GuideImportant Safety InstructionsBefore beginning any fitness program, see yourphysician for a complete physical examination.Il est conseillé de subir un examen médical completavant d’entreprendre tout programme d’exercise. Sivous avez des étourdissements ou des faiblesses,arrêtez les exercices immédiatement.When using exercise equipment, basic precautionsshould always be taken, including the following:• Read all instructions before using the S3.15equipment. These instructions are written for yoursafety and to protect the unit.• Do not allow children or those unfamiliar with itsoperation on or near the equipment. Do not leavechildren unsupervised around the unit.• Use the equipment only for its intended purpose asdescribed in this manual. Do not use accessoryattachments that are not recommended by themanufacturer, as such attachments may causeinjuries.• Wear proper exercise clothing and shoes for yourworkout and avoid loose clothing. Tie long hairback.• Use care when getting on or off the unit.• Do not overexert yourself or work to exhaustion.• If you feel any pain or abnormal symptoms,stop your workout immediately and consultyour physician.• Never operate the unit when it has been droppedor damaged. Return the equipment to a servicecenter for examination and repair.• Never drop or insert objects into any opening.Keep hands away from moving parts.• Always check the unit and its cables before eachuse. Make sure that all fasteners and cables aresecure and in good working condition.• Do not use outdoors.Personal Safety During Assembly• It is strongly recommended that a qualifieddealer assemble the equipment. Assistance isrequired.• Read each step in the assembly instructions andfollow the steps in sequence. Do not skip ahead. Ifyou skip ahead, you may learn later that you haveto disassemble components and that you mayhave damaged the equipment.• Assemble and operate the S3.15 on a solid, levelsurface. Locate the unit a few feet from walls orfurniture to provide easy access.Obtaining ServiceDo not attempt to service the S3.15 yourselfexcept for the maintenance tasks describedin this guide. This unit does not contain anyuser-serviceable parts.For information about product operation,or service, refer to the Precor web site atwww.precor.com. Should you need moreinformation regarding customer supportnumbers or a list of Precor authorizedservice centers, visit the Precor web siteat www.precor.com/cons.If you call or e-mail Customer Support,have the serial number and part numbersavailable.You can find the serial number printed ona label affixed to the side of the S3.15. Forfuture reference, write the serial number inthe space provided below.Serial number: _______________________IMPORTANT SAFETY INSTRUCTIONSImportant Safety Instructionspage 2

S3.15 Assembly and Maintenance GuideTable of ContentsImportant Safety Instructions .................................................................................. 2Personal Safety During Assembly ............................................................................................................ 2Obtaining Service ..................................................................................................................................... 21234Before You Begin ....................................................................................................... 4Unpacking the Equipment ......................................................................................................................... 4Optional Equipment .................................................................................................................................. 4Preparations .............................................................................................................. 5Required Tools .......................................................................................................................................... 5Installation Requirements ......................................................................................................................... 5Assembly Tips ........................................................................................................................................... 5Assembly Instructions .............................................................................................. 6Open the Box ............................................................................................................................................ 71. Assemble Main Structure.............................................................................................................. 82. Assemble Leg Extension .............................................................................................................. 103. Install Seat and Rollers ................................................................................................................. 114. Assemble Weight Stack ................................................................................................................ 135. Assemble Press Arm .................................................................................................................... 156. Install Main Cable ......................................................................................................................... 177. Install Ab Cable and Floating Pulleys ........................................................................................... 198. Install Leg Extension Cable .......................................................................................................... 209. Install Leg Press Option Cable Connection .................................................................................. 2210. Attach Upper Shrouds .................................................................................................................. 2311. Attach Accessories ....................................................................................................................... 2412. Apply Weight Decals and Lubricant .............................................................................................. 25Cable Adjustments and Maintenance ...................................................................... 261. Cable Tension ............................................................................................................................... 272. Cable Adjustments ........................................................................................................................ 283. Maintenance ................................................................................................................................. 29Appendix – Shrouds ................................................................................................................................. 31Limited Warranty Statement ..................................................................................................................... 32Warranty Registration Card ...................................................................................................................... 33Specifications .............................................................................................................................. Back coverTable of Contentspage 3

S3.15 Assembly and Maintenance Guide1Before You BeginS3.15Thank you for purchasing the S3.15. This unit is part ofthe Precor Strength line of quality strength trainingmachines, which let you target specific muscle groupsto achieve better muscle tone and overall bodyconditioning. To maximize your use of the equipment,please study this guide thoroughly.Unpacking the EquipmentThe S3.15 is carefully tested and inspected beforeshipment. Precor Strength ships the unit in severalpieces that require assembly. Ask for assistance duringthe assembly process.• Review the Installation Requirements.• When instructed to open a box, carefully unpackthe pieces and lay them on the floor near thelocation where you plan to use the equipment.Be careful to open boxes and assemble components inthe sequence presented in this manual.If any items are missing, contact the dealer from whomyou purchased the unit. For more information, refer toObtaining Service.Optional Equipment• S3.15 Leg Press Option• S3.15 Multi-Hip Option• Heavy Stack Option (Additional 50 lb weight stack)• ShroudsLeg Press OptionMulti-Hip OptionBefore You Beginpage 4

S3.15 Assembly and Maintenance Guide2 PreparationsCAUTION: To set up this unit, you will needassistance. Do not attempt assembly by yourself.You must review and follow the instructions in thisguide. If you do not assemble and use the S3.15according to the following guidelines, you could voidthe Precor Limited Warranty.Required ToolsTools that you need to obtain before assembling theunit include:❏❏❏❏❏❏❏❏❏⁹⁄₁₆-inch socket³⁄₄-inch socket⁹⁄₁₆-inch box-end wrench³⁄₄-inch box-end wrenchCrescent wrenchRubber malletWire tie cutter (cuts plastic tie wraps)Utility knifeStep stoolInstallation RequirementsFollow these installation requirements whenassembling the unit:• Fill out and mail the warranty registration card.• Set up the S3.15 on a solid, flat surface.A smooth, flat surface under the unit helps keepit level.• Provide ample space around the machine.Open space around the machine allows for easieraccess.• Insert all fasteners in the same direction. Foraesthetic purposes, insert all the fasteners in thesame direction unless specified (in text orillustrations) to do otherwise.• Leave room for adjustments. Tighten fasteners(such as screws, nuts, and bolts), so the unit isstable, but leaves room for adjustments. Do notfully tighten fasteners until instructed (in the steps)to do so.Assembly Tips• Fasteners may become loose and fall off duringshipment. Inspect the plastic wrap and packagingfor loose parts. To alleviate confusion duringassembly, reattach the loose fasteners and pulleysfound in the packaging.• A black 6-inch scale with white numbers isprovided at the bottom of every assemblyinstruction page. Use this scale to identify thecorrect fastener size. The head of a fastener is notused in measuring the length.• Most fasteners are ³⁄₈-inch unless otherwise noted.To find out the length of a particular fastener,measure its shank (the long, narrow part beneaththe head). Refer to the following diagram:Fastener headFastener threadsShankTo determine thelength of a fastener,measure its shank.• Silver-colored zinc fasteners are used with thetitanium parts (Press Arm, Floating Pulleys, etc.).Black fasteners are used when assembling thestone gray painted surfaces.• Some pieces have extra holes that you will not use.Use only those holes indicated in the instructionsand illustrations.• Read all caution notes on each page beforecompleting that step.• While you may be able to assemble the S3.15 byreading the illustrations only, refer to the text forimportant safety cautions and notes.Preparationspage 5

S3.15 Assembly and Maintenance GuideOpen the BoxUse wire tie cutters to open the box.The illustration shows how the S3.15 will look whenyou have completed its assembly. The callouts identifyspecific pieces.Important: Most fasteners are fitted to the frame orpulleys, you will need to disassemble the fastenersbefore proceeding with each step.Lat BarTop AssemblyPress Arm AssemblyRow HandleMain UprightRear UprightHandlebarsLeg ExtensionWeight StackRear CrossbarLeg Extension ArmMain BaseTriceps StrapAnkle StrapCurl Bar1 2 3 4 5 6Open the Boxpage 7

S3.15 Assembly and Maintenance Guide1. Assemble Main StructureA. Attach the Main Base to the Rear Crossbar usingtwo 4³⁄₄-inch hex head boltsfour flat washerstwo locknutsB. Install the Rear Upright to the Main Base usingtwo 4³⁄₄-inch hex head boltsfour flat washerstwo locknutsNote: Position the uprights so the Shroud mountsface the center of the unit.C. Attach the Main Upright to the Main Baseusingtwo 2¹⁄₄-inch hex head boltsfour flat washerstwo locknutsRear CrossbarA2 - 4³⁄₄" bolts4 - washers2 - locknutsMain BaseRear UprightShroudMountsMain UprightC2 - 2¹⁄₄" bolts4 - washers2 - locknuts2 - 4³⁄₄" bolts4 - washers2 - locknutsBMain Base1 2 3 4 5 6Step 1. Assemble Main Structurepage 8

S3.15 Assembly and Maintenance GuideD. For ease of assembly, disassemble and removethe top pulley and its fasteners on the MainUpright.EAlign Top Beam withuprights.E. Install the Top Beam on the Rear and MainUprights and reinstall the top pulley and fastenerassembly.Top BeamNote: If necessary, use a rubber mallet to align themounting holes.F. Secure the Top Beam to the Rear Upright usingtwo 2¹⁄₄-inch hex head boltsfour flat washerstwo locknutsG. Secure the Top Beam to the Main Upright usingtwo 4-inch hex head boltsfour radius washerstwo locknutsNote: Make sure the radius washers lie flat againstthe Main Upright before wrench tightening.H. Wrench tighten all bolts. Start with the fastenersthat secure the Top Beam and follow the order ofthe assembled steps in reverse.RearUprightMainUprightDJ2 - 2¹⁄₄" bolts4 - washers2 - locknutsFG2 - 4" bolts4 - radius washers2 - locknutsJ. Replace the top pulley and finger tighten thefasteners.1 2 3 4 5 6Step 1. Assemble Main Structure, continuedpage 9

S3.15 Assembly and Maintenance Guide2. Assemble Leg ExtensionA. Attach the Leg Extension to the Main Base usingtwo 2½-inch boltstwo spring washersWrench tighten.B. Insert the 2-inch threaded shaft into the LegExtension Arm.BThreadedShaftC. Attach the Leg Extension Arm to the LegExtension usingtwo ¹⁄₂-inch x ¾-inch buttonhead boltstwo flat washersWrench tighten using the 8mm hex keys.Leg Extension ArmA2 - 2½" bolts2 - spring washers2 - ¹⁄₂" x ¾-inchbuttonhead bolts2 - washersCMain BaseLegExtensionLeg Extension Arm1 2 3 4 5 6Step 2. Assemble Leg Extensionpage 10

S3.15 Assembly and Maintenance Guide3. Install Seat and RollersA. Attach the Seat Pad to the Seat Stem usingfour 1-inch zinc buttonhead boltstwo zinc flat washersWrench tighten using a 6mm hex key.B. Insert the Seat Stem into the Seat UprightAssembly. Pull out the seat adjustment pin toinsert the stem. Place the Seat Stem at its lowestposition.C. Attach the Back Pad to the Main Upright usingtwo 2½-inch hex head boltstwo flat washersWrench tighten.2 - 2½" bolts2 - washersCBackPadSeat PadSeat StemA4 - 1" zincbuttonhead bolts2 - zinc washersPull out the seatadjustment pin toinsert stem.B1 2 3 4 5 6Step 3. Install Seat and Rollerspage 11

S3.15 Assembly and Maintenance GuideD. Slide a Plastic Washer and a Roller Pad onto oneend of a Roller Pad Rod. Insert one MushroomCap to plug the end hole. If necessary, pound theMushroom Cap in place using the rubber mallet.E. Insert the Roller Pad Rod through the hole in theLeg Extension Arm.F. Slide the remaining Plastic Washer and Roller Padon the other end of the Roller Pad Rod. Insert oneMushroom Cap to plug the end hole. If necessary,pound the Mushroom Cap in place using therubber mallet.G. Attach the Floor Plate usingtwo ³⁄₄-inch buttonhead boltsWrench tighten using a 6mm hex key.DRollerPad RodPlastic WasherRoller PadMushroom CapFFloorPlateEG2 - ³⁄₄" buttonhead bolts1 2 3 4 5 6Step 3. Install Seat and Rollers, continuedpage 12

S3.15 Assembly and Maintenance Guide4. Assemble Weight StackImportant: Obtain adult assistance before installingthe Guide Rods and Weights.A. Place the Guide Rods into the two outside holes inthe Main Base.CAUTION: The lubricant on the Guide Rods canstain clothes. Wear proper attire when workingwith or lubricating the Guide Rods.B. Place one Guide Rod Spacer and one WeightCushion on each Guide Rod and allow it to slidedown and rest on the Main Base.Note: Guide Rod Spacers do not need to beinstalled if the Heavy Stack Option is purchasedthrough your dealer.C. Add the 10-lb weights. For ease of weight pinplacement and use, orient the curve on the weightplate to the desired side of the unit. Position theweight plate so the plastic bushing is on top andhold your finger over the plastic bushing to preventit from popping out.CAUTION: The weights are heavy! Handlethe weights carefully so as not to drop themor injure yourself. Pick up and place oneweight at a time on the Guide Rods. Do notangle the Guide Rods to such a degree thatthey dislodge the Guide Rod Spacers orWeight Cushions. Have someone hold theGuide Rods in place while you slide theweights on the stack.WeightCushionsBAGuide RodGuide Rod Spacers(Do not install spacers if youpurchased the Heavy Stack Option.)WeightC1 2 3 4 5 6Step 4. Assemble Weight Stackpage 13

S3.15 Assembly and Maintenance GuideD. Orient the hole in the Top Cap Weight with thecurve in the weight plates. Place the Top CapWeight onto the Guide Rods and slide the SelectorStem into the weight stack.E. Slide the Guide Rod Bracket onto the Guide Rodsand secure it to the Upper Frame Crosspiece usingtwo ³⁄₄-inch buttonhead boltstwo flat washersWrench tighten.DGuideRodTop CapWeightE2 - ¾" buttonheadbolts2 - washersUpper FrameCrosspieceGuide Rod BracketSelectorStem1 2 3 4 5 6Step 4. Assemble Weight Stack, continuedpage 14

S3.15 Assembly and Maintenance Guide5. Assemble Press ArmImportant: Obtain adult assistance to attach the PressArm Assembly.A. Attach the Press Arm Assembly, with the labelfacing out, to the Top Beam usingone threaded shafttwo 1-inch buttonhead boltstwo zinc flat washersWrench tighten.1 - threaded shaft2 - 1" buttonhead bolts2 - zinc washersTop BeamALabel on Press Arm AssemblyPress ArmAssembly1 2 3 4 5 6Step 5. Assemble Press Armpage 15

S3.15 Assembly and Maintenance GuideB. Slide the Handlebars in place on the Press Arm.Handlebars curve inward. Review the illustrationfor correct handlebar placement.C. Attach the Row Handles usingeight ¼ x ½-inch buttonhead screwseight radius washersNote: Make sure the radius washers lie flat againstthe Row Handle before wrench tightening.D. Wrench tighten the screws using the 5mm hexkeys.BPress Arm AssemblyHandlebarsRow HandlesC8 - ¼ x ½" buttonhead screws8 - radius washers1 2 3 4 5 6Step 5. Assemble Press Arm, continuedpage 16

S3.15 Assembly and Maintenance Guide6. Install Main CableNote: All pulleys are installed in the frameassemblies. As you begin each new step, removethe fasteners and pulley. Feed the cable aroundthe pulley as shown, and then replace thefasteners and finger tighten. Wrench tighten allpulley fasteners once you have completed theinstallation of each cable assembly.A. Start at the Top Beam and feed the threaded endof Main Cable 130197 over one 4½-inch pulley.Attach the pulley to the Top Beam usingone 4-inch hex head bolttwo 1¹⁄₄-inch shoulder spacersone locknutB. Feed the cable over the second 4½-inch pulley.Attach the pulley to the Top Beam usingone 4-inch hex head bolttwo 1¹⁄₄-inch shoulder spacersone locknutC. Feed the cable over the upper 3½-inch pulleylocated in the Press Arm assembly. Attach thepulley to the Press Arm assembly usingone 2-inch zinc hex head bolttwo zinc flat washersone zinc locknutD. Feed the cable over the upper 3½-inch pulleylocated in the Main Upright. Attach the pulley to theMain Upright usingone 4-inch hex head bolttwo 1¹⁄₄-inch shoulder spacersone locknutPulley assemblies4½-inch Pulley1 - bolt2 - shoulder spacers1 - locknutCAB3½-inch Pulley (used on graypainted parts)1 - bolt2 - shoulder spacers1 - locknut3½-inch Pulley (used ontitanium parts)1 - zinc bolt2 - zinc washers1 - zinc locknutD3½-inch Pulley (used on graypainted parts)1 - bolt2 - washers1 - locknut1 2 3 4 5 6Step 6. Install Main Cablepage 17

S3.15 Assembly and Maintenance GuideE. Feed the cable over the lower 3½-inch pulleylocated in the Press Arm assembly. Attach thepulley to the Press Arm assembly usingone 2-inch zinc hex head bolttwo zinc flat washersone zinc locknutF. Feed the cable over the upper 3½-inch pulleylocated in the Main Upright. Attach the pulley to theMain Upright usingone 4-inch hex head bolttwo 1¹⁄₄-inch shoulder spacersone locknutG. Pull the slack out of the Main Cable so the ball endof the cable rests against the Lat Bar Holder.H. Disassemble the upper pulley in the DoubleFloating Pulley as shown. Feed the cable aroundthe 3½-inch pulley and reattach it usingone 2-inch zinc hex head bolttwo zinc flat washersone zinc locknutJ. Feed the cable through the hole in the UpperFrame Crosspiece and over the two 3½-inchpulleys attached to the Top Beam assembly.Reattach the pulleys to the assembly usingtwo 2-inch hex head boltsfour flat washerstwo locknutsK. Feed the cable down through the hole in the UpperFrame Crosspiece and attach the threaded end ofthe cable into the Selector Stem. Continue turningthe screw three to four full turns to secure thethreads inside the Selector Stem.L. Wrench tighten all pulley fasteners.Important: Do not tighten the jam nut on thethreaded end of the cable or the Double FloatingPulley fasteners, at this time.Step 6. Install Main Cable, continued1 - 2" zinc bolt2 - zinc washers1 - zinc locknutEDouble Floating PulleyAssembly1 - 2" zinc bolt2 - zinc washers1 - zinc locknutFH1 2 3 4 5 6KJ2 - bolts4 - washers2 - locknutsGPull slack and place theexcess cable on the floorwhile you assemble theDouble Floating Pulley.page 18

S3.15 Assembly and Maintenance Guide7. Install Ab Cable and FloatingPulleysA. Start at the center pulley on the Main Upright.Feed the threaded end of Ab Cable 130196through the opening and over one 3½-inch pulley.Attach the pulley to the Main Upright usingone 4-inch hex head bolttwo flat washersone locknutB. Disassemble the 3½-inch pulley located inside theSingle Floating Pulley. Feed the cable around thepulley and reattach the pulley usingone 1¹⁄₂-inch zinc hex head bolttwo zinc washersone thin zinc locknutWrench tighten.C. Disassemble the lower portion of the DoubleFloating Pulley. Feed the cable around the lowerpulley and reattach it usingone 2-inch zinc hex head bolttwo zinc flat washersone zinc locknutD. Attach the threaded end of the cable to a SingleFloating Pulley. Continue turning the screw three tofour full turns to secure it inside the floating pulleyhousing.F. Remove any twists in the cables, and then wrenchtighten all pulley fasteners.Single FloatingPulley Assembly1 - 1½" zinc bolt2 - zinc washers1 - zinc locknut1 - 4" bolt2 - washers1 - locknutAC1 - 2" zinc bolt2 - zinc washers1 - zinc locknutBD1 2 3 4 5 6Step 7. Install Ab Cable and Floating Pulleyspage 19

S3.15 Assembly and Maintenance Guide8. Install Leg Extension CableA. Before feeding the cable through the pulleyassemblies, remove the U-bracket assembly, cablestop ball and rubber washer at the end of the LegExtension Cable 130198.B. Start at the Pivoting Bracket attached to theMain Base. Feed the end of the cable beneath the3½-inch pulley.C. Feed the cable through the Single Floating Pulleyas shown.D. Disassemble the upper 3½-inch pulley locatedinside the Gusset which is welded to the BaseFrame.E. Feed the cable under the lower pulley.F. Loop the cable over the upper 3½-inch pulley andsecure it to the Gusset usingone 2¼-inch bolttwo flat washersone locknutRubber WasherCable Stop BallU-bracketAGussetDC1 - 2¼" bolt2 - washers1 - locknutFEB1 2 3 4 5 6Step 8. Install Leg Extension Cablepage 20

S3.15 Assembly and Maintenance Guide11. Attach AccessoriesA. At the end of the Top Beam, attach the Lat Bar tothe Main Cable using a spring clip.Note: The two small hooks at the end of the TopBeam can be used to store the Lat Bar when it’snot in use.B. Install the Triceps Straps to the Ab Cable using thespring clip.To vary your exercise routine, you can replace theLat Bar and attach the Triceps Straps to the MainCable.C. Attach the Curl Bar to the Leg Extension Cableusing the short piece of chain and two spring clips(installed at each end of the chain).To work out leg muscle groups, you can attach aSoft Ankle Strap, to the end of the cable, instead ofthe curl bar.D. For aesthetics, insert plastic plugs into the unusedmounting holes in the Top Beam, Main Base, andRear Crossbar.ALatBarCurlBarTricepsStrapBCAnkleStrap1 2 3 4 5 6Step 11. Attach Accessoriespage 24

S3.15 Assembly and Maintenance Guide2. Cable AdjustmentsYou may need to adjust the cables after installation andperiodically thereafter. If the cables remain slack afteryou have followed the steps found in Cable Tension,perform the following:A. Loosen the jam nut on the Weight Stack threadedend to expose additional threads. Adjust thethreaded end until the slack is removed.B. Loosen the jam nuts on the Floating Pulleysthreaded ends. Adjust the threaded ends until theslack is removed. Make sure the amount of threadsexposed on one pulley is about the same as theother pulley.C. Check the Top Cap Weight to make sure it remainswell-seated on the Weight Stack and then retightenthe jam nuts.D. Check the Selector Stem alignment by insertingthe Weight Pin into every hole on the Weight Stack.ThreadsJam NutATop CapWeightTop WeightCBJam NutTop Cap Weight is fullyseated on the top weight.No gap should appear.Thread exposure should remain thesame for both Floating Pulleys.12345D67891011121314151 2 3 4 5 6Cable Adjustments and Maintenance, continuedpage 28

S3.15 Assembly and Maintenance Guide3. MaintenanceGuide RodsLubricate the Guide Rods every six months.InspectionInspect the unit daily.LubricantGuide RodLook and listen for loose fasteners, cable tensionissues, unusual noises and any other indications thatthe equipment may be in need of service.You are responsible for the proper maintenance of theunit as discussed in this manual. For other serviceissues, contact Customer Support. Refer to ObtainingService.1234567891011121314151 2 3 4 5 6Cable Adjustments and Maintenance, continuedpage 29

S3.15 Assembly and Maintenance GuideShroudsCAUTION: Clean the Shrouds with productspecifically labeled as safe for acrylic. Use a clean,nonabrasive cloth and light pressure to avoidscratching the acrylic surface.The acrylic Shrouds on the S3.15 are easily scratchedor damaged through improper cleaning techniques. Toavoid problems, dust the shrouds often with a clean,lint-free cloth and light pressure. Avoid rubbing dirt orgrit into the surface. If you use glass cleaner or asimilar product, make sure the label states that it issafe to use on Plexiglas® or acrylic products.Important: DO NOT use ketones, aromatics, esters,halogens, window cleaning sprays, alcohol, kitchenscouring compounds, or solvents (such as acetone,benzene, gasoline, carbon tetrachloride, or thinners).Do not use ammonia-based cleaning solutionsbecause the ammonia destroys the plastic coating.To remove light scratches on the smooth side only, usea buffing compound such as, car wax. Lightly buff theacrylic sheet using a clean buffer until the scratchesdisappear.1 2 3 4 5 6Cable Adjustments and Maintenance, continuedpage 30

Precor Residential Equipment Limited WarrantyPLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USINGYOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARECONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS.Limited Warrantyarranty.Precor Incorporated warrants all new Precor products to be free from defects in materials andmanufacture for the warranty period set forth below. The warranty period commences on theinvoice date of original purchase. This warranty applies only against defects discovered withinthe warranty period and extends only to the original purchaser of the product. Parts repaired orreplaced under the terms of this warranty will be warranted for the remainder of the originalwarranty period only. To make claim under warranty, the buyer must notify Precor or theirauthorized Precor dealer within 30 days after the date of discovery of any nonconformity andmake the affected product available for inspection by Precor or its service representative.Precor’s obligations under this warranty are limited and set forth below.Warranty Periods and CoverageAll residential products and commercial products used in the home are warranted for thefollowing periods:• Lifetime frame and welds• 10 years parts and wear items• 1 year labor• Coverage for options and accessories defined below.Options / AccessoriesMany options or accessories have components that are connected internally or mounted inside theelectronic console. The following guidelines determine the warranty for these components. If theinternal components are installed by the factory or by an authorized dealer as part of the originalsale and delivery, they have a warranty that is identical to the warranty of the equipment in whichthey are connected or mounted. If the internal components are not installed by the factory or by anauthorized dealer as part of the original sale and delivery, they have a 90-day parts and laborlimited warranty. All components that are not internally connected have 90-day parts only limitedwarranty. Satisfactory proof of purchase is required in all cases.Conditions and RestrictionsThis warranty is valid only in accordance with the conditions set forth below:1. The warranty applies to the Precor product only while:a. It remains in the possession of the original purchaser and proof of purchase isdemonstratedb. It has not been subjected to accident, misuse, abuse, improper service, or non-Precormodificationsc. Claims are made within the warranty period2. This warranty does not cover damage or equipment failure caused by electrical wiring not incompliance with electrical codes or Precor owner’s manual specifications, or failure to providereasonable and necessary maintenance as outlined in the owner’s manual.Complete this portion and keep for your recorecords.Purchased From: ____________________________ Example: Dealer or store name.Phone Number: _____________________________ Example: Dealer or store telephone number.Product/model: _____________________________ Example: M9.31Serial number: ______________________________ The serial number is found on the shipping container3. Warranty of all Precor products applies to residential use only and is void when products areused in a nonresidential environment or installed in a country other than where sold.4. Except in Canada, Precor does not pay labor outside the United States.5. Warranties outside the United States and Canada may vary. Please contact your local Dealerfor details.This limited warranty shall not apply to:1. Software version upgrades2. Cosmetic items, including, but not limited to the following: grips, seats, and labels.3. Repairs performed on Precor equipment missing a serial number or with a serial tag that hasbeen altered or defaced.4. Service calls to correct installation of the equipment or instruct owners on how to use theequipment.5. Pickup, delivery, or freight charges involved with repairs.6. Any labor costs incurred beyond the applicable labor warranty period.Disclaimer and ReleaseThe warranties provided herein are the exclusive warranties given by Precor and supersede any prior,contrary or additional representations, whether oral or written. ANY IMPLIED WARRANTIES, INCLUDING THEWARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT APPLY TO ANY PARTS DESCRIBED ABOVEARE LIMITED IN DURATION TO THE PERIODS OF EXPRESS WARRANTIES GIVEN ABOVE FOR THOSE SAME PARTS. PRECORHEREBY DISCLAIMS AND EXCLUDES THOSE WARRANTIES THEREAFTER. Some states do not allow limitation on howlong an implied warranty lasts, so the above limitation may not apply to you. PRECOR ALSO HEREBY DISCLAIMSAND EXCLUDES ALL OTHER OBLIGATIONS OR LIABILITIES, EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, WITHRESPECT TO ANY NONCONFORMANCE OR DEFECT IN ANY PRODUCT, INCLUDING BUT NOT LIMITED TO: (A) ANY OBLIGATION,LIABILITY, RIGHT, CLAIM OR REMEDY IN TORT, WHETHER OR NOT ARISING FROM THE NEGLIGENCE OF PRECOR OR ITSSUPPLIERS (WHETHER ACTIVE, PASSIVE OR IMPUTED); AND (B) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM, OR REMEDY FORLOSS OF OR DAMAGE TO ANY EQUIPMENT. This disclaimer and release shall apply even if the express warranty setforth above fails of its essential purpose.Exclusive RemediesFor any product described above that fails to conform to its warranty, Precor will provide, at their option, one ofthe following: (1) repair; (2) replacement; or (3) refund of the purchase price. Precor Limited Warranty servicemay be obtained by contacting the authorized dealer from whom you purchased the item. Precorcompensates Servicers for warranty trips within their normal service area to repair equipment at the owner’slocation. You may be charged a trip charge outside the service area. THESE SHALL BE THE SOLE AND EXCLUSIVEREMEDIES OF THE BUYER FOR ANY BREACH OF WARRANTY.Exclusion of Consequential and Incidental DamagesPRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARISING IN CONTRACT(INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRICT LIABILITY), OROTHERWISE, FOR DAMAGE TO THE EQUIPMENT, PROPERTY DAMAGE, LOSS OF USE, REVENUE OR PROFIT, COST OFCAPITAL, COST OF SUBSTITUTE EQUIPMENT, ADDITIONAL COST INCURRED BY BUYER (BY WAY OF CORRECTION OROTHERWISE) OR ANY OTHER INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHERRESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE OR INABILITY TO USE THE PRODUCT. This exclusionapplies even if the above warranty fails of its essential purpose and regardless of whether such damagesare sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any otherlegal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages,so the above limitation might not apply.This warranty gives you specific legal rights, and you may also have other rights, which vary stateto state.Effective 01 January 2003P/N 36287-110page 32

Precor Incorporated20031 142nd Avenue NEPO Box 7202Woodinville, WA 98072-4002PLACESTAMPHERERET.Fold along dotted line and tape closed before mailing.To allow us to serve you better, please take a few moments tocomplete and return your warranty registration.YOU MAY ALSO REGISTER ONLINE ATwww.precor.com/warrantyIf you have questions or need additional information, contact yourlocal dealer or call Precor Customer Support at 800-347-4404.Thank You and Welcome to Precor

Please detach and mail in the warranty registration within ten days of purchase.TELL US ABOUT YOUR NEW PRECOR PRODUCTDate ofPurchase:Month Day YearProductSerialNumber:The serial number is located on the shipping box and on the product.Purchasedfrom:Please indicate the type of product purchased:❑ Elliptical Fitness CrossTrainer (EFX ® )❑ Treadmill❑ Strength Training SystemDealer Name❑ StretchTrainer TM❑ Cycle❑ Stair ClimberTELL US ABOUT YOU❑ Mr.❑ Mrs.❑ Ms.First NameMiddle Initial Last NameStreet AddressCity StateArea Code TelephoneYour Email AddressTELL US ABOUT YOUR PURCHASEZip CodeApt./Suite:Gender: Marital status: Age: Annual household income: What are your fitness goals?❑ Male ❑ Married ❑ Under 18 ❑ Under $50,000 ❑ Weight loss/management❑ Female ❑ Divorced ❑ 18-24 ❑ $51,000-75,000 ❑ Muscle tone enhancement❑ Widowed ❑ 25-34 ❑ $76,000-100,000 ❑ Cardiovascular improvement❑ Never been married ❑ 35-44 ❑ $101,000-150,000 ❑ Overall health❑ 45-54 ❑ $151,000+ ❑ Increase energy and flexibility❑ 55-64 ❑ Stress reduction❑ 65+ ❑ Rehabilitation❑ OtherPurchase (check all that apply): How did you FIRST become aware of Precor❑ First Precor product products (choose only one):❑ Replaces a Precor product of the same type ❑ A gift❑ Replaces same type of product – different brand ❑ Friend/relative❑ Addition to equipment currently owned ❑ Physician❑ Fitness club❑ InternetWhat factors MOST influenced your decision to ❑ News report or product reviewpurchase your Precor product (choose up to three): ❑ Magazine advertisement or article❑ Precor reputation ❑ Print advertisement❑ Prior use of Precor product(s) ❑ In-store display or demonstration❑ Design/appearance ❑ Other❑ Value for the price❑ Special product features❑ Rebate or sale price❑ Quality/durability❑ Warranty❑ Physician recommendationEffective 01 July 2004P/N 45623-102

S3.15 SpecificationsLength: 72 inches (182 cm)Height: 83 inches (211 cm)Width: 51 inches (130 cm)Shipping weight: 221 lb (100 kg)Precor Incorporated20031 142nd Avenue NEP.O. Box 7202Woodinville, WA USA 98072-40021-800-347-4404Precor is a registered trademark of Precor Incorporated.Specifications subject to change without notice.Copyright 2006 Precor Incorporated.www.precor.comNOTICE:Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S. andforeign patents for both the mechanical construction and the visual aspects of its product design. Any party contemplating the use ofPrecor’s product designs is hereby forewarned that Precor considers the unauthorized appropriation of its proprietary rights to be avery serious matter. Precor will vigorously pursue all unauthorized appropriation of its proprietary rights.S3.15 Literature Kit 49456-101S3.15 Assembly & Maintenance Manual 49457-101Registration Card 45623-102Warranty Statement 36287-11018 September 2006