IEM - Wear Products - Anchor Danly

NAAMS Series W05, W06 & W07/VDI 3357Wear Plates – Metricwww.danly.comMATERIALS:TOLERANCES: Self-lubricating wear plates are manufacturedfrom aluminum bronze or steel with graphiteplugs. The plugs cover 20-25% of the wearsurface. Wear plates are also available in plain steel. Wear plates are also available in the GMsizes in cast iron with graphite. See the crossreference sheet on pg. 11 for the GM partnumber.ADDITIONAL AUTOMOTIVE STANDARDS Thickness± 0.00/ -0.02 mm Mounting hole locations ± 0.2 mm Flatness± 0.013 mm Unless otherwise noted ± 0.25 mmMOUNTING SCREWS: M8 S.H.C.S. for part numbersVYG20-50-80 and VYG20-80-50.M12 S.H.C.S. for all other part numbers.Width Length Aluminum Bronze Steel Steel Mounting Hole Pattern & LocationW L w/Graphite Plugs w/Graphite Plugs Plain Hole Hole A B C D E(mm) (mm) Part Number Part Number Part Number Qty. Pattern (mm) (mm) (mm) (mm) (mm)100 250 WDX13-80-03100250Y* WDX13-80-03100250G* WDX13-80-03100250X* 2 A-2 25 225 – 50 –100 250 90.20.65-100250Y* – 90.20.65-100250X* 4 C-4 25 225 25 – 75100 315 WDX13-80-03100315Y* WDX13-80-03100315G* WDX13-80-03100315X* 2 A-2 25 290 – 50 –125 200 90.20.65-125200* – 90.20.65-125200* 4 C-4 25 175 25 – 100125125250 WDX13-80-03125250Y* WDX13-80-03125250G* WDX13-80-03125250X* 3 B-3 25 225 25 62.5 100125 250 90.20.65-125250Y* – 90.20.65-125250X* 4 C-4 25 225 25 – 100125 315 WDX13-80-03125315Y* WDX13-80-03125315G* WDX13-80-03125315X* 3 B-3 25 290 25 62.5 100160 200 90.20.65-160200Y* – 90.20.65-160200G* 4 C-4 25 175 25 – 135160 250 WDX13-80-03160250Y* WDX13-80-03160250G* WDX13-80-03160250X* 3 B-3 25 225 25 80 135160 250 90.20.65-160250Y* – 90.20.65-160250X* 4 C-4 25 225 25 – 135160 300 90.20.65-160300Y* – 90.20.65-160300X* 4 C-4 25 275 25 – 135200 200 90.20.65-200200Y* – 90.20.65-200200X* 4 C-4 25 175 25 – 175200 250 90.20.65-200250Y* – 90.20.65-200250X* 4 C-4 25 225 25 – 175200 300 90.20.65-200300Y* – 90.20.65-200300X* 4 C-4 25 275 25 – 175PLEASE NOTE: These wear plates have hole patterns that differ from our standard VDI/NAAMS wear plates. They mustbe ordered using the GM or Ford part number to receive the correct mounting hole locations.9