IEM - Wear Products - Anchor Danly

More documents

Recommendations

Info

www.danly.comCONTENTSPAGE NUMBERKeeper Plates & Blocks INCH METRICSelf-Lubricating Keeper Plates 42Self-Lubricating Metric Keeper Plates 43Light Duty K-Series Self-Lubricating Keeper Blocks 44Medium Duty KM-Series Self-Lubricating Keeper Blocks 46Heavy Duty KH-Series Self-Lubricating Keeper Block 48Self-Lubricating 6mm LIP Keeper Blocks 50Self-Lubricating 13mm LIP Keeper Blocks 52Cam DwellsSelf-Lubricating Cam Dwell <strong>Wear</strong>plates 54Stop Blocks & RetainersStop Blocks 55Pad Retainers – Locking, Standard Mount 56Pad Retainers – Locking, Standard Mount with Flats 58Pad Retainers – Locking, Reverse Mount with Flats 60Pad Retainers – Standard Mount 61Pad Retainers – Reverse Mount 62ii
<strong>Wear</strong> PlateInstallation & Selection Guidewww.danly.comSteel with Graphite Plugs & Aluminum Bronze with Graphite Plugs1. When installing and/or after cleaning, we recommend that a coat of 20 wt. oil be appliedto the wear surface to help start the lubricating process.2. If grinding is necessary, grind only the back or edges of the wear plate, not the pluggedside of the wear plate.3. It is not necessary to lubricate the wear plate after the initial coat of oil is applied.Plain Steel & Steel with Graphite Plugs1. It is important that wet grinding techniques be used if grinding is necessary.2. When wet grinding, do not remove more than .0002" to .0004" (0.005 to 0.010mm) ateach pass.FAILURE TO COMPLY WITH THESE RECOMMENDATIONSMAY RESULT IN CRACKING OF THE WEAR PLATERecommended Conditions for Maximum Performance1. Aluminum Bronze with graphite plugs against plain (ungrooved) steel.2. Steel with graphite plugs against plain (ungrooved) steel.3. Aluminum Bronze with graphite plugs against cast die – not recommended if loadexceeds 300 psi (20 bar).4. Steel with graphite plugs against cast die – not recommended if load exceeds 200 psi(13.5 bar). Must have balanced load.1
Page 1 and 2: WEAR PRODUCTSInch & Metric SizesSel
Page 3: CONTENTSwww.danly.comPAGE NUMBERWea
Page 7 and 8: N-Series Standard & Self-Lubricatin
Page 9 and 10: NAAMS Series W01, W02 & W03Standard
Page 11 and 12: JIS Series Standard & Self-Lubricat
Page 13 and 14: NAAMS Series W05, W06 & W07/VDI 335
Page 15 and 16: AutomotiveWear Plate Conversionswww
Page 17 and 18: Plain Bronze &Self-Lubricating Wear
Page 19 and 20: Self-LubricatingWearstrip Ways - In
Page 21 and 22: Plain Bronze &Self-Lubricating Wear
Page 23 and 24: NAAMS SeriesSelf-Lubricating Wearst
Page 25 and 26: Self-LubricatingGib Assemblies - In
Page 27 and 28: Self-Lubricating Baseplatefor Gib A
Page 29 and 30: Self-LubricatingSquare Gibs - Inchw
Page 31 and 32: Self-LubricatingL-Gibs - Metricwww.
Page 33 and 34: Self-Lubricating 13mmLIP Cam Slide
Page 35 and 36: Self-LubricatingU & V Blocks - Inch
Page 37 and 38: NAAMSU & V Blocks - Metricwww.danly
Page 39 and 40: Self-Lubricating 45mmGuide Blocks -
Page 41 and 42: Self-Lubricating 60mmGuide Blocks -
Page 43 and 44: Medium Duty Self-LubricatingGuide B
Page 45 and 46: Self-LubricatingCenter Key & Guide
Page 47 and 48: Self-LubricatingKeeper Plates - Met
Page 49 and 50: Light Duty K Series Self-Lubricatin
Page 51 and 52: Medium Duty KM SeriesSelf-Lubricati
Page 53 and 54: Heavy Duty KH SeriesSelf-Lubricatin
Page 55 and 56:
Self-Lubricating 6mmLIP Keeper Bloc
Page 57 and 58:
Self-Lubricating 13mmLIP Keeper Blo
Page 59 and 60:
Stop Blocks - Inchwww.danly.comProd
Page 61 and 62:
Pad Retainers -Locking Inch, Standa
Page 63 and 64:
Pad Retainers -Locking Inch, Standa
Page 65 and 66:
Pad Retainers -Standard Mount - Met
Page 67 and 68:
WEAR PRODUCTSThe IEM Value Proposit
show all

IEM - Wear Products - Anchor Danly

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?