IEM - Wear Products - Anchor Danly

www.danly.comSelf-Lubricating L-Gibsfor Gib Assembly – InchProduct FeaturesThese inch-sized L-gibs are used in the gib assembliesshown on page 21, or can be purchased separately to createcustom cam systems. They are supplied with mounting holesand are spot drilled for dowels for simplified installation process.2GAL24GTFOR MOUNTING SCREWSMATERIALS: Aluminum bronze material with oilimpregnated graphite plugs. The plugscover 25-30% of the wear surface.TOLERANCES: Thickness Mounting hole locations Unless otherwise noted± 0.005 in.± 0.005 in.± 0.010 in.MOUNTING SCREWS:1/4" or M6 S.H.C.S recommended for3/4" width GIBS.5/16" or M8 S.H.C.S recommended forall other GIBS.Gib Part Length Width A B C D E G H J K M N HoleNumber L (in) W (in) (in) (in) (in) (in) (in) (in) (in) (in) (in) (in) (in) Qty.2GAL16GT 2.00 0.750 0.312 0.75 0.188 0.28 0.56 – 1.625 – 1.00 – 0.26 22GAL24GT 3.00 0.750 0.312 0.750 0.188 0.28 0.56– 2.625 – 0.88 2.12 0.26 22GAL32GT 4.00 0.750 0.312 0.75 0.188 0.28 0.56 2.000 3.625 – 0.88 3.12 0.26 33GAL24GT 3.00 1.000 0.375 0.75 0.250 0.37 0.75 – 2.625 – 0.88 2.12 0.26 23GAL32GT 4.00 1.000 0.375 0.75 0.250 0.370.752.000 3.625 – 0.88 3.12 0.26 33GAL40GT 5.00 1.000 0.375 0.75 0.250 0.37 0.75 2.500 4.625 – 0.88 4.12 0.26 34GAL24GT 3.00 1.255 0.500 0.88 0.375 0.37 0.88 – 2.625 – 0.88 2.12 0.32 24GAL32GT 4.00 1.2551.2550.5000.5000.88 0.3750.88 0.3750.370.370.88 2.000 3.6250.88– 0.88 3.12 0.32 34GAL40GT 5.00 1.255 0.500 0.88 0.375 0.37 0.88 2.500 4.625 – 0.88 4.12 0.32 34GAL48GT 6.00 1.255 0.500 0.88 0.375 0.37 0.88 2.125 5.625 3.875 0.88 5.12 0.32 46GAL32GT 4.00 1.500 0.750 1.25 0.500 0.44 1.00 2.000 3.625 – 0.88 3.12 0.32 36GAL40GT 5.00 1.500 0.750 1.25 0.500 0.441.002.500 4.625 – 0.88 4.12 0.32 36GAL48GT 6.00 1.500 0.750 1.25 0.500 0.44 1.00 2.125 5.625 3.875 0.88 5.12 0.32 422