CF2000 Instruction Manual - Illumination Technologies

More documents

Recommendations

Info

LAMPOUTWHEELHOMEMounting and ClearanceCF2000 SeriesThe unit can be permanently mounted by removing the feet. This can be done as long asadequate airflow below (intake) and in the rear (exhaust) of the unit is allowed. Use M4hardware and ensure a minimum of 10mm clearance under the base to allow for propercooling. Never mount the receptacle pointing down.The light source also needs to have adequate space in the front of the unit to allow thecalibrator to plug in. The clearance on top is needed allow the cover to open fully forservicing the lamp and filters.OUT OFREGULATION!WHEELCONTROLCALIBRATIONCONNECTORFig 1 – CF2000 LightsourceFig 1 – CF2000 Mounting Holes5Copyright 2005 ITPN 850-CF2000Illumination Technologies Inc. Rev 3
OperationsCF2000 SeriesThis CF2000 series light sources are set to your application by you setting the communicationprotocol and intensity needed. This unit includes the Light-Lock system. It is automaticallyno when the light source is on. It can not be disabled. It will automatically remember theintensity that you have set after a power cycle.This unit also has the 8 position filter wheel that you can insert light modifying filters into. Theoperation of this wheel is controlled through the external communications and a manual jogbutton. It will not remember its position if there is a power cycle.The CF2000 also has a auto calibration feature, that adjusts the light output to a externalreference. This allows the light output to remain constant after a lamp change.The unit has indicator LED’s on the front of the unit to indicate the status of the light source an dwheel control button to allow manual movement of the wheel during set up.This unit also has design feature to prevent poor quality lamps from damaging its electronicsMany lamps as they fail will short out internally. This can cause the power circuits to drive overtheir design target and will cause component failure. The CF2000 detects this and prevents thelight source from damaging it self.5.1 Set Up:This unit should be connected to reliable source of AC. Any compatible IEC 320 power cordmaybe used. See specification section for voltage and current requirement.Communication that will be used for operating the unit should be selected. The unit is set atRS232 as a factory default. See Remote operations section for the detailsThe color filters of choice can be positioned in the light path by selecting its position location #2- #8. Note position # 1 must be left open for the calibrator to function correctly. The wheel willaccept 20mm filters with a It filter spacer or 25mm filters. If you are using 20mm filters installspacer per appendix C before installing. Before the filters are installed into the wheel thepositions must be understood. Upon initial power up of the CF2000, the built in microprocessorcommands the filter wheel to seek “Home” position. This places the #1, filter holder slot directlybetween the lamp and the lightguide receptacle.As you open the CF2000 Unit, the filter wheel has the positions marked on the inside of thewheel. Facing the unit from the front, the filter slot at the top of the wheel when the wheel is in“Home” is actually slot #7. See below The filter wheel will rotate clockwise as faced from thefront of the unit.The end of the fiber accessory to be used should be inserted in to the receptacle and locked inplace with the thumb screw. It is important that the diameter of the accessory match thereceptacle to assure uniform and stable output.6Copyright 2005 ITPN 850-CF2000Illumination Technologies Inc. Rev 3
Page 2 and 3: Illlumination TechnologiesIndexCont
Page 4 and 5: LAMPOUTCALIBRATIONCONNECTORCF2000 S
Page 8 and 9: OperationsOperating Position Front
Page 10 and 11: OperationsThe communications board
Page 12 and 13: OperationsThe unit can be set to ru
Page 14 and 15: CalibrationCF2000 SeriesCalibration
Page 16 and 17: Technical DataCF2000 Series7.1 Ligh
Page 18 and 19: Technical Data7.3 Color FiltersTher
Page 20 and 21: Service and TroubleshootingSymptom
Page 22 and 23: CF2000 SeriesSpare Parts/Accessorie
Page 24: AppendixCF2000 SeriesAPPENDIX AA) C
Page 28 and 29: AppendixB.2) SAMPLE PROGRAMSCommand
Page 30 and 31: AppendixMyString = MyString & MyCha

CF2000 Instruction Manual - Illumination Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?