Series 2000 Communications Handbook - Soliton

More documents

Recommendations

Info

Modbus & EI Bisynch AddressesSeries 2000 Communications Handbook5. Chapter 5 Modbus and EIBisynch Addresses5.1. INTRODUCTIONThis section of the manual provides a list of all parameters in 2200 and 2400 seriescontrollers that are available over the communications link. As far as possible, it follows thesame organisation as the controller user interface itself. Definitions of parameters and statusinformation not available via the controller display are also provided.All 2000 Series controllers may be configured for a wide variety of functions and someparameters will only be available if the related function is configured. Modbus addresses thatare not supported have no parameter assigned. In normal operating mode all configurationparameters are read only. To be able to write to these parameters, the controller must be inconfiguration mode.If the Modbus protocol is used to read a parameter that is not configured, an undefined valuewill be returned. The EI-Bisynch protocol will return an EOT character to signal that theparameter is not available.Modbus function 6 single parameter write operations to unconfigured or read only parameterswill be rejected with a Modbus ‘data error’ return code. The EI-Bisynch protocol rejects suchrequests with the NAK character.NB: Blocks of data written using Modbus function 16 containing values in positionscorresponding to the addresses of unconfigured parameters are not generally rejected,although the values of any unconfigured parameters are discarded. This allows relativelylarge blocks of parameter data to be written in a single operation, even if the block containsa little ‘empty’ space. This is particularly useful for operations such as ramp/dwell programdownloading, recipes, or instrument cloning. However this also leads to a potential pitfall: ifthe block of data contains only a single parameter, and the destination address refers to anunconfigured or unused Modbus address, the write operation will appear to be successful,although the controller will have discarded the value.Attempts to write to read only parameters over Modbus, even when they are embedded withina block of data, will be rejected with a Modbus ‘data error’. Any subsequent values in theblock will also be discarded.Rules for read and write operation in the Modbus IEEE area are dealt with in Chapter 3.5.2. MODBUS AND BISYNCH ADDRESSES.This section of the manual provides a list of all parameters in 2200 and 2400 seriescontrollers that are available over the communications link. As far as possible, it follows thesame organisation as the instrument user interface itself. Definitions of parameters and statusinformation not available via the instrument display are also provided.5-2 Series 2000 Communications Handbook Part No HA026230 Issue 2.0 Feb-00
Series 2000 Communications HandbookModbus & EI Bisynch Addresses5.3. OPERATING MODE PARAMETERSIt is often only necessary to access a limited number of the most common parameters, where,for example, it is required to emulate the front panel of a controller in a mimic diagram. Thefollowing table shows a summary of common parameters:2408OP1 OP2DDExample 1 PID ControllerParameter Modbus Address Bisynch AddressRead Process 1 PVvalueChange Setpoint 2 - (enter new value) SL - (enter newvalue)Raise Setpoint 2 - (new value inrepeated steps)SL - (new value inrepeated steps)Select ManualMode273 - (enumerator 1) mA - (enumerator1)Change Output 3 - (new value) OP - (new value)PowerRaise OutputPower3 - (new value inrepeated steps)OP - (new value inrepeated steps)Read OutputPower3 OPExample 2 Valve PositionerParameter Modbus address Bisynch AddressTo Select Manual 273 - (enumerator 1) mA - (enumerator1)To Change Output 60 - (new value) VM - (new value)PositionTo Read OutputPosition53 VPTable 5-1: Operating Mode Parameters5.4. MODBUS AND BISYNCH PARAMETER TABLESNotes: The following notes apply throughout this section1. Issued software versions to date are 2400: 1.03, 2.04, 3.04 and 3.05 and 2200: 1.00,1.20, 1.30 and 2.10.2. Bi-synch only available in 2200 software versions 2 onwards3. Greyed out cells indicate parameter not available4. In Bisynch Lists, the numerals “zero” and “one” are shown in italics as 0 and 1. Thisis to distinguish between I (as in In), l (as in low) and O (as in Out)Series 2000 Communications Handbook Part No HA026230 Issue 2.0 Feb-00 5-3
Page 1 and 2:
Series 2000 Communications Handbook
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13:
Page 16 and 17:
Digital Communications HardwareSeri
Page 18 and 19:
Digital Communications HardwareSeri
Page 20 and 21: Digital Communications HardwareSeri
Page 28 and 29: MODBUS and JBUS ProtocolSeries 2000
Page 58 and 59: EI-Bisynch ProtocolSeries 2000 Comm
Page 72 and 73: Modbus & EI Bisynch AddressesSeries
Page 120 and 121:
Modbus & EI Bisynch AddressesSeries
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
DevicenetSeries 2000 Communications
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Modbus and EIBisynch Advanced Topic
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Glossary of TermsSeries 2000 Commun
Page 156:
ASCII CodesSeries 2000 Communicatio
show all

Series 2000 Communications Handbook - Soliton

Create successful ePaper yourself

Delete template?

Save as template?