ADL300 Elevator Drives for Synchronous ... - Sprecher + Schuh

More documents

Recommendations

Info

IndexError message shown onthe display [on the integratedkeypad]Sub-code0040H-64DescriptionSolution: Remove the optional cards from the incorrect slots and insert them in the correct slots11 Load def plcCondition: may occur during loading of the parameter database saved in the Flash of the Mdplc applicationNormally appears at initial power-on after downloading a new application.If this message is displayed when the drive is already operating, this means that a problem has occurred in the parameter database saved in Flash.If this message appears the drive restores the default database, i.e. the one that was downloaded.[LDPL] 0001H-1 The database saved is not validSolution: Set the parameters to the value required and perform Save parameter12 Plc cfg errorCondition: may occur during loading of the Mdplc applicationThe Mdplc application present on the drive is not run.[PLCE] 0004H-4 The application downloaded has a different Crc on DataBlock and Function table0065H-101 The application downloaded has an invalid identifier (Info)0066H-102 The application downloaded has an incorrect task number (Info)0067H-103 The application downloaded has an incorrect software configuration0068H-104 The application downloaded has a different Crc on DataBlock and Function table0069H-105 A Trap error or System error has occurred.The drive automatically performs a Power-up operation.The application is not run.See in Alarm List for further information regarding the error occurred006AH-106 The application downloaded has an incorrect identifier (Task)006BH-107 The application downloaded has an incorrect task number (Task)006CH-108 The application downloaded has an incorrect Crc (Tables + Code)Solution: Remove the Mdplc application or download a correct Mdplc application13 Plc 1 [PLC1]14 Plc 2 [PLC2] Reserved messages and dedicated to the PLC application. See the application manual.15 Plc 3 [PLC3]16 Plc 4 [PLC4]17 Opt bus fault Condition: this may occur when the drive is turned on, during fieldbus card setup. Error during configuration or communication error.[OPTB] XXX0H-X If the first digit to the left of "H" in the alarm sub-code is 0, the error regards a communication problem.XXX0H-X If the first digit to the left of "H" in the alarm sub-code is other than 0, the error regards a configuration problem.Solution: For configuration errors, check the configuration of the bus communication, type of bus, baudrate, address, parameter settingFor communication errors, check wiring, termination resistors, disturbance immunity, timeout settings.For further details, please refer to the user guide for the specific bus.Condition: this may occur when powering the drive, if the incorrect enable key is inserted for a given firmware function.18 Wrong key xxxxH-x[KEYF]Solution: Ask Gefran to supply the correct key to enable the desired firmware function.19 Key expiringCondition: this may occur at drive power-on if the incorrect enabling key was inserted for a given firmware function. At this stage the firmware functioncan still be used freely, but this time limit is about to expire[KEYE] xxxxH-x Number of hours for which the function can still be used freely.Solution: Ask Gefran for the correct key to enable the desired firmware function.20 SD card errorCondition: this condition may occur when sending data from the drive to the SD card or from the SD card to the drive. It could be due to a memory cardthat is incompatible or not present.XXX0H-X Communication errorSolution: Check the memory card being used20 Parameter error Condition: if an error occurs during activation of the parameter database saved in flash; the alarm is inserted in the alarm list and alarm log.[PE]XXX0H-X Code XXXXH-X indicates the number of the parameter (Hex-Dec) that has caused the error: make a note of this to discuss it with theservice centre.Solution: Set the parameter that has caused the error to the correct value and execute Save parameters, switch the drive off and then back on.21 Encoder error Condition: this condition may occur when the drive is powered during encoder setup each time parameter 552 Regulation mode is set.[ENCE]100H-256 Cause: An error occurred during setup; the information received from the encoder is not reliable. If the encoder is used for feedback theSpeed fbk loss alarm is also generated.Solution: Take the recommended action for the Speed fbk loss alarm.200H-512 Cause: The firmware on the optional encoder card is incompatible with that on the regulation card. The information received from theencoder is not reliableSolution: Contact Gefran in order to update the firmware on the optional encoder card.23 Options cfg changedCondition: this may occur when powering the drive if an expansion card has been removed or replaced or the incorrect enable key is inserted for a givenfirmware function.[OCFG] 0064H-100 Card removed from slot 10014H-20 Card removed from slot 20078H-120 Card removed from slot 1 and from slot 2Solution: Check the hardware configuration, then press ESC. Save the parameters (Save parameters, menu 04.01 par 550) to save the new hardwareconfiguration.24 Fw update failed Condition: When updating the firmware, check whether the file is in the wrong format or corrupt.Solution: try again with a correct file.108 ADL300 • Quick installation guide - Specifications and connection
AppendixA.1 - ADL300 Advanced ConfigurationADL300 is coded as the Advanced version and does not implement any I/O or encoder expansion cards.The user may integrate any of the available options, to meet specific system requirements (an I/O card must always bepresent to use the drive). These integrations can be performed quickly and simply, by inserting the cards in the relativeconnectors on the regulation card (provided as standard with the drive and not interchangeable).Note!Connections and technical data of I/O and encoder expansion cards are given in sections A.2 and A.3.The firmware automatically recognises the ADL300 Basic or Advanced drive. The type of drive is displayed in the “Drive info” menu, parameter 476 Drivetype (0= Basic, 1 = Advanced, 2 = Basic-VGA).ADL300 AdvancedType / DescriptionCodeADL300A – ... –KBL–4230-400-480 Vac, 3phADL300A – ... –KBL–F–4–C230-400-480 Vac, 3phEMI Filter - CANADL300A – ... –KBL–2T200-230 Vac, 3phADL300A – ... –KBL–F–2T–C200-230 Vac, 3phEMI Filter - CANADL300A – ... –KBL–2M200-230 Vac, 1phADL300A – ... –KBL–2M-C200-230 Vac, 1phCANRegulationR-ADL300-ABasic regulation cardRC-ADL300-ARegulation card with integrated CAN-- • O • O • O-- O • O • O •EXP-IO-D4-ADL2 digital inputs + 2 digital outputsEXP-IO-D5R3-F-ADL5 Digital inputs + 3 Relay outputsS567L S5L08 I/O cardEXP-IO-D8R4-ADL8 Digital inputs + 4 Relay outputsEXP-IO-D8A4R4-ADL8 digital inputs + 2 analog outputs + 4 analog inputs + 2 relay outputsS568L S570L EXP-IO-D12A2R4-ADL8 digital inputs + 4 digital outputs + 4 analog inputs + 2 relay outputsEXP-IO-D16R4-ADL12 digital inputs + 4 digital outputs + 4 relay outputsEXP-DE-I1R1F2-ADLDigital encoder 3 Channels + Repeat + 2 FreezeEXP-DE-I1-ADLDigital encoder 2 ChannelsS569L S566L S5L04 S5L36 Encoder cardsEXP-SESC-I1R1F2-ADLSinusoidal SinCos encoder 3 Channels + Repeat + 2 FreezeEXP-SESC-I1R1-V-ADLSinusoidal SinCos encoder 3 Channels + Repeat (VGA connectors)EXP-EN/SSI-I1R1F2-ADLSinusoidal encoder - Absolute EnDat + Repeat + 2 FreezeEXP-SE-I1R1F2-ADLSinusoidal encoder 3 Channels + Repeat + 2 FreezeEXP-HIP-I1R1F2-ADLHiperface encoder 3 Channels + Repeat + 2 FreezeS5L06 S5L39 S5L07 S571L S572L • = standard, = optional , O= not possibleADL300 • Quick installation guide - Specifications and connection 109
Page 2 and 3:
Information about this manualThe AD
Page 4 and 5:
7.3.2 Typical connection diagram...
Page 6 and 7:
Specific instructions that apply to
Page 8:
2 - Introduction to the productThe
Page 11:
2.4 Product identificationThe basic
Page 14 and 15:
ADL300 BasicADL300 Basic-VGARegulat
Page 17 and 18:
4.4 Input electrical dataChoke Siz
Page 19 and 20:
4.5.2 Derating values for switching
Page 21 and 22:
4.8 CoolingAll inverters are equipp
Page 24 and 25:
Figure 4.9.5: Size 5 dimensions311
Page 26 and 27:
5.2 Input chokesThe three-phase mai
Page 28 and 29:
5.4 External braking resistors (opt
Page 30 and 31:
6 - Mechanical installationThe Driv
Page 32 and 33:
Recommended screws for fasteningSiz
Page 34 and 35:
CautionFunctioning of the Drive wit
Page 36 and 37:
Note!The power terminal strip is ex
Page 38 and 39:
7.1.4 Block diagram of power sectio
Page 40:
7.1.8 Motor connectionL1 L2 L3 BR C
Page 43 and 44:
Figure 7.2.2-B: terminal strip and
Page 46 and 47:
7.3 Connection diagramsNote!This ch
Page 48 and 49:
BRK CNT EN ILIM n=0 ALCANPrgEnterFi
Page 50 and 51:
BRK CNT EN ILIM n=0CANPrgEnterALFig
Page 52 and 53:
BRK CNT EN ILIM n=0 ALCANPrgEnterFi
Page 54 and 55:
Warning!To use this type of connect
Page 56 and 57:
MASTERCANopenADL300ADL300CAN-LCAN-H
Page 58 and 59: SizeIrms(A)Ipk(A)ADL300-...-2M, 1ph
Page 60 and 61: 8.1.2 KB-ADL optional programming k
Page 62 and 63: Note !Flashing points and character
Page 64 and 65: • Modifying Enum valuesWhen you p
Page 66 and 67: 8.2.8 Motor self-tuningSet PAR 2024
Page 68 and 69: 8.3.3 Scanning of the parameters01
Page 70 and 71: 8.3.8 Configuration of the display8
Page 72: If an error occurs during transfer,
Page 75 and 76: This equipment must not be used as
Page 77 and 78: Step 2 - Setting motor parametersNo
Page 79 and 80: q 1 1 . 54. Enter 88.8.0 Enter 00.0
Page 81 and 82: 9.1 Asynchronous motor startup wiza
Page 83 and 84: Note!When data entry is complete th
Page 85 and 86: qSEQ06 PAR: 11160Motor inertia0 kgm
Page 87 and 88: Final checkNote!If you wish to use
Page 89: Step 2 - Setting motor parametersNo
Page 92 and 93: ●●Set the distance valueq 1 1 .
Page 94 and 95: Step 1 - Electrical connectionsMake
Page 96 and 97: Note !For more information see para
Page 98 and 99: qSEQ08 PAR: 11042Acceleration0.6 m/
Page 100 and 101: 10 - Troubleshooting10.1 AlarmsNote
Page 102 and 103: CodeError message shownon the displ
Page 104 and 105: ●●Speed fbk loss [22] alarm wit
Page 106 and 107: 10.3 MessagesNote ! For more inform
Page 110 and 111: A.1.1 - Inserting expansion cards
Page 112 and 113: ●●EXP-IO-D8A4R4-ADL1 enable inp
Page 114 and 115: PrecisionIsolation1% of full scaleN
Page 116 and 117: A.3.2 PhasingIn order for the ADL30
Page 118 and 119: INCREMENTAL DIGITAL ENCODER (DE) SI
Page 120 and 121: INCREMENTAL DIGITAL ENCODER (DE) SI
Page 122 and 123: EXP-SESC-I1R1F2-ADLIncremental Sinu
Page 124 and 125: EXP-EN/SSI-I1R1F2-ADLIncremental si
Page 126 and 127: Repeat Encoder RE (TTL/HTL line-dri
Page 128: A.4.2 Configuration of the brake fa
show all

ADL300 Elevator Drives for Synchronous ... - Sprecher + Schuh

Create successful ePaper yourself

Delete template?

Save as template?