- Page 2 and 3:
Information about this manualThe AD
- Page 4 and 5:
7.3.2 Typical connection diagram...
- Page 6 and 7:
Specific instructions that apply to
- Page 8:
2 - Introduction to the productThe
- Page 11:
2.4 Product identificationThe basic
- Page 14 and 15:
ADL300 BasicADL300 Basic-VGARegulat
- Page 17 and 18:
4.4 Input electrical dataChoke Siz
- Page 19 and 20:
4.5.2 Derating values for switching
- Page 21 and 22:
4.8 CoolingAll inverters are equipp
- Page 24 and 25:
Figure 4.9.5: Size 5 dimensions311
- Page 26 and 27:
5.2 Input chokesThe three-phase mai
- Page 28 and 29:
5.4 External braking resistors (opt
- Page 30 and 31:
6 - Mechanical installationThe Driv
- Page 32 and 33:
Recommended screws for fasteningSiz
- Page 34 and 35:
CautionFunctioning of the Drive wit
- Page 36 and 37:
Note!The power terminal strip is ex
- Page 38 and 39:
7.1.4 Block diagram of power sectio
- Page 40:
7.1.8 Motor connectionL1 L2 L3 BR C
- Page 43 and 44:
Figure 7.2.2-B: terminal strip and
- Page 46 and 47:
7.3 Connection diagramsNote!This ch
- Page 48 and 49:
BRK CNT EN ILIM n=0 ALCANPrgEnterFi
- Page 50 and 51:
BRK CNT EN ILIM n=0CANPrgEnterALFig
- Page 52 and 53:
BRK CNT EN ILIM n=0 ALCANPrgEnterFi
- Page 54 and 55:
Warning!To use this type of connect
- Page 56 and 57:
MASTERCANopenADL300ADL300CAN-LCAN-H
- Page 58 and 59:
SizeIrms(A)Ipk(A)ADL300-...-2M, 1ph
- Page 60 and 61:
8.1.2 KB-ADL optional programming k
- Page 62 and 63:
Note !Flashing points and character
- Page 64 and 65:
• Modifying Enum valuesWhen you p
- Page 66 and 67:
8.2.8 Motor self-tuningSet PAR 2024
- Page 68 and 69:
8.3.3 Scanning of the parameters01
- Page 70 and 71: 8.3.8 Configuration of the display8
- Page 72: If an error occurs during transfer,
- Page 75 and 76: This equipment must not be used as
- Page 77 and 78: Step 2 - Setting motor parametersNo
- Page 79 and 80: q 1 1 . 54. Enter 88.8.0 Enter 00.0
- Page 81 and 82: 9.1 Asynchronous motor startup wiza
- Page 83 and 84: Note!When data entry is complete th
- Page 85 and 86: qSEQ06 PAR: 11160Motor inertia0 kgm
- Page 87 and 88: Final checkNote!If you wish to use
- Page 89: Step 2 - Setting motor parametersNo
- Page 92 and 93: ●●Set the distance valueq 1 1 .
- Page 94 and 95: Step 1 - Electrical connectionsMake
- Page 96 and 97: Note !For more information see para
- Page 98 and 99: qSEQ08 PAR: 11042Acceleration0.6 m/
- Page 100 and 101: 10 - Troubleshooting10.1 AlarmsNote
- Page 102 and 103: CodeError message shownon the displ
- Page 104 and 105: ●●Speed fbk loss [22] alarm wit
- Page 106 and 107: 10.3 MessagesNote ! For more inform
- Page 108 and 109: IndexError message shown onthe disp
- Page 110 and 111: A.1.1 - Inserting expansion cards
- Page 112 and 113: ●●EXP-IO-D8A4R4-ADL1 enable inp
- Page 114 and 115: PrecisionIsolation1% of full scaleN
- Page 116 and 117: A.3.2 PhasingIn order for the ADL30
- Page 118 and 119: INCREMENTAL DIGITAL ENCODER (DE) SI
- Page 122 and 123: EXP-SESC-I1R1F2-ADLIncremental Sinu
- Page 124 and 125: EXP-EN/SSI-I1R1F2-ADLIncremental si
- Page 126 and 127: Repeat Encoder RE (TTL/HTL line-dri
- Page 128: A.4.2 Configuration of the brake fa