ADL300 Elevator Drives for Synchronous ... - Sprecher + Schuh

More documents

Recommendations

Info

Size@Uln =200-230VacIn Rated output current(fsw = default)Pn mot(Recommended motor power ,fsw =default)@Uln =200-230Vac@Uln =200-230VacReduction factor(A) (kW) (Hp) (1) (2)ADL300-...-2T, 3ph2055 24.5 - - 5.5 - 7.5 0.95 1.23075 32 - - 7.5 - 10 0.95 1.23110 45 - - 11 - 15 0.95 1.24150 60 - - 15 - 20 0.95 1.24185 75 - - 18.5 - 25 0.95 1.24220 90 - - 22 - 30 0.95 1.25300 105 - - 30 - 40 0.95 1.25370 150 - - 37 - 50 0.95 1.2KvKaltIGBT brakingunitStandardinternal (withexternalresistor);brakingtorque 150%MAXExternaloptionalSize@Uln =230VacIn Rated output current(fsw = default)Pn mot(Recommended motor power ,fsw =default)@Uln =230VacReduction factor(A) (kW) (1) (2)ADL300-...-2M, 1ph1011 6 - - 1.1 - - 0.95 1.21015 6.8 - - 1.5 - - 0.95 1.22022 9.6 - - 2.2 - - 0.95 1.22030 13 - - 3 - - 0.95 1.23040 15 - - 4 - - 0.95 1.23055 22 - - 5.5 - - 0.95 1.2KvKaltIGBT brakingunitStandardinternal (withexternalresistor);brakingtorque 150%MAX(1) Kt: Derating factor for ambient temperature of 50°C (1% every °C above 45°C)(2) Kalt: Derating factor for installation at altitudes above 1000 meters a.s.l. Value to be applied = 1.2% each 100 m increase above 1000 m.E.g.: Altitude 2000 m, Kalt = 1.2% * 10 = 12% derating; In derated = (100 - 12) % = 88 % In4.5.1 Derating values in overload conditionIn overload conditions the output current depends on the output frequency, as shown in the figure below.Figure 4.5.1-A: Ratio between overload/output frequency (ADL300-...-4 - ADL300-...-2T)OL (% I N)Sizes 1...3 (4...22kW)OL (% I N)Sizes 4-5 (30...75kW)2001801501503F out (Hz)3F out (Hz)Figure 4.5.1-B: Ratio between overload/output frequency (ADL300-...-2M)OL (% I N)2001503F out (Hz)18 ADL300 • Quick installation guide - Specifications and connection
4.5.2 Derating values for switching frequencyThe switching frequency is modified according to the temperature of the drive (measured on the heat sink), as shown inthe figure below.Figure 4.5.2: Ratio between switching frequency/heat sink temperatureF SW (kHz)105T diss thT diss (°C)4.5.3 Kalt: Ambient temperature reduction factorFigure 4.5.3: Tamb reduction coefficientKT1.000.95Function not allowedRange of ambient temperatures allowed-10 45 50T amb (°C)4.6 Voltage level of the inverter for safe operationsThe minimum time between the moment in which an ADL inverter is disabled from the mains and that in which anoperator can operate on internal parts of the inverter, without the danger of electric shock, is 5 minutes.AttentionThis value takes into account the time to turn off an inverter supplied at 460 Vac + 10%, without any options (time indicated for disabledinverter condition).ADL300 • Quick installation guide - Specifications and connection 19
Page 2 and 3: Information about this manualThe AD
Page 4 and 5: 7.3.2 Typical connection diagram...
Page 6 and 7: Specific instructions that apply to
Page 8: 2 - Introduction to the productThe
Page 11: 2.4 Product identificationThe basic
Page 14 and 15: ADL300 BasicADL300 Basic-VGARegulat
Page 17: 4.4 Input electrical dataChoke Siz
Page 21 and 22: 4.8 CoolingAll inverters are equipp
Page 24 and 25: Figure 4.9.5: Size 5 dimensions311
Page 26 and 27: 5.2 Input chokesThe three-phase mai
Page 28 and 29: 5.4 External braking resistors (opt
Page 30 and 31: 6 - Mechanical installationThe Driv
Page 32 and 33: Recommended screws for fasteningSiz
Page 34 and 35: CautionFunctioning of the Drive wit
Page 36 and 37: Note!The power terminal strip is ex
Page 38 and 39: 7.1.4 Block diagram of power sectio
Page 40: 7.1.8 Motor connectionL1 L2 L3 BR C
Page 43 and 44: Figure 7.2.2-B: terminal strip and
Page 46 and 47: 7.3 Connection diagramsNote!This ch
Page 48 and 49: BRK CNT EN ILIM n=0 ALCANPrgEnterFi
Page 50 and 51: BRK CNT EN ILIM n=0CANPrgEnterALFig
Page 52 and 53: BRK CNT EN ILIM n=0 ALCANPrgEnterFi
Page 54 and 55: Warning!To use this type of connect
Page 56 and 57: MASTERCANopenADL300ADL300CAN-LCAN-H
Page 58 and 59: SizeIrms(A)Ipk(A)ADL300-...-2M, 1ph
Page 60 and 61: 8.1.2 KB-ADL optional programming k
Page 62 and 63: Note !Flashing points and character
Page 64 and 65: • Modifying Enum valuesWhen you p
Page 66 and 67: 8.2.8 Motor self-tuningSet PAR 2024
Page 68 and 69:
8.3.3 Scanning of the parameters01
Page 70 and 71:
8.3.8 Configuration of the display8
Page 72:
If an error occurs during transfer,
Page 75 and 76:
This equipment must not be used as
Page 77 and 78:
Step 2 - Setting motor parametersNo
Page 79 and 80:
q 1 1 . 54. Enter 88.8.0 Enter 00.0
Page 81 and 82:
9.1 Asynchronous motor startup wiza
Page 83 and 84:
Note!When data entry is complete th
Page 85 and 86:
qSEQ06 PAR: 11160Motor inertia0 kgm
Page 87 and 88:
Final checkNote!If you wish to use
Page 89:
Step 2 - Setting motor parametersNo
Page 92 and 93:
●●Set the distance valueq 1 1 .
Page 94 and 95:
Step 1 - Electrical connectionsMake
Page 96 and 97:
Note !For more information see para
Page 98 and 99:
qSEQ08 PAR: 11042Acceleration0.6 m/
Page 100 and 101:
10 - Troubleshooting10.1 AlarmsNote
Page 102 and 103:
CodeError message shownon the displ
Page 104 and 105:
●●Speed fbk loss [22] alarm wit
Page 106 and 107:
10.3 MessagesNote ! For more inform
Page 108 and 109:
IndexError message shown onthe disp
Page 110 and 111:
A.1.1 - Inserting expansion cards
Page 112 and 113:
●●EXP-IO-D8A4R4-ADL1 enable inp
Page 114 and 115:
PrecisionIsolation1% of full scaleN
Page 116 and 117:
A.3.2 PhasingIn order for the ADL30
Page 118 and 119:
INCREMENTAL DIGITAL ENCODER (DE) SI
Page 120 and 121:
INCREMENTAL DIGITAL ENCODER (DE) SI
Page 122 and 123:
EXP-SESC-I1R1F2-ADLIncremental Sinu
Page 124 and 125:
EXP-EN/SSI-I1R1F2-ADLIncremental si
Page 126 and 127:
Repeat Encoder RE (TTL/HTL line-dri
Page 128:
A.4.2 Configuration of the brake fa
show all

ADL300 Elevator Drives for Synchronous ... - Sprecher + Schuh

Create successful ePaper yourself

Delete template?

Save as template?