ADL300 Elevator Drives for Synchronous ... - Sprecher + Schuh

5.4 External braking resistors (optional)Recommended combinations for use with internal braking unit.Table 5.4.1: Recommended combination ADL...-AC and ADL...-BR seriesSizeList and technical data of standard external resistorsResistor type Code Q.ty Max. overload, 1" -service 10%Ebr (kJ)ADL300-...-4, 3phMax. overload, 30" -service 25%Ebr (kJ)1040 RFPD 750 DT 100R S8SY4 1 7.5 38 750 100 IP441055 RFPR 750 D 68R S8SZ3 1 7.5 38 750 68 IP442075 RFPR 750 D 68R S8SZ3 1 7.5 28 750 68 IP442110 RFPR 1200 D 49R S8SZ4 1 7.5 28 1200 49 IP443150 RFPR 1900 D 28R S8SZ5 1 12 43 1900 28 IP443185 BRT4K0-15R4 S8T00G 1 40 150 4000 15.4 IP203220 BRT4K0-15R4 S8T00G 1 40 150 4000 15.4 IP204300 BRT4K0-11R6 S8T00H 1 40 150 4000 11.6 IP204370 BRT4K0-11R6 S8T00H 1 40 150 4000 11.6 IP204450 BRT8K0-7R7 S8T00I 1 40 150 8000 7.7 IP205550 BRT8K0-7R7 S8T00I 1 40 150 8000 7,7 IP205750 External braking unit (BUy series, optional)ADL300-...-2T, 3ph2055 RFPR 1200 D 49R S8SZ4 1 12 43 1200 49 IP443075 RFPR 1900 D 28R S8SZ5 1 19 75 1900 28 IP443110 BRT4K0-15R4 S8T00G 1 40 150 4000 15.4 IP204150 BRT4K0-11R6 S8T00H 1 40 150 4000 11.6 IP204185 BRT4K0-11R6 S8T00H 1 40 150 4000 11.6 IP204220 BRT8K0-7R7 S8T00I 1 40 150 8000 7.7 IP205300 BRT8K0-7R7 S8T00I 1 40 150 8000 7.7 IP205370 External braking unit (BUy series, optional)ADL300-...-2M, 1ph1011 RF 220 T 100R S8T0CE 1 1.5 11 200 100 IP441015 RF 220 T 68R S8T00T 1 1.5 11 200 68 IP442022 RF 300 D 34R S8T0CH 1 2.5 24 300 34 IP442030 RF 300 D 34R S8T0CH 1 2.5 24 300 34 IP443040 RFPD 750 DT 26R S8T0CZ 1 4.5 43 750 26 IP443055 RFPD 750 DT 26R S8T0CZ 1 4.5 43 750 26 IP44Pnbr(W)Rbr(Ω)HousingPnbrRbrEbrBraking resistor rated powerBraking resistor ohmic valueMaximum energy that can be dissipated on the resistorBraking resistors may be subject to unexpected overloads due to faults.Warning!Resistors MUST be protected using thermal cutouts. These devices must not interrupt the circuit in which the resistor isinserted but their auxiliary contact must cut off the power supply to the power section of the drive. If the resistor requires aprotection contact, this must be used together with that of the thermal cutout.A la suite de pannes, les résistances de freinage peuvent être sujettes à des surcharges imprévues. La protection des résistancesau moyen de dispositifs de protection thermique est absolument capitale. Ces dispositifs ne doivent pas interrompre lecircuit qui abrite la résistance, mais leur contact auxiliaire doit couper l’alimentation du côté puissance du drive. Si la résistanceprévoit un contact de protection, ce dernier doit être utilisé conjointement à celui du dispositif de protection thermique.Note!Refer to the Gefran LIFT catalogue (cod. 1S9CLM) for resistor weights and dimensions.28 ADL300 • Quick installation guide - Specifications and connection