ADAM-5000 Series I/O Module User's Manual

More documents

Recommendations

Info

I/O Module IntroductionCalibration voltage (ADAM-5017UH)Module5017HInput Range Code(Hex)Input Range08h ±10 V +10 V48h 0 ~ 10 V +10 V46h 0 ~ 20 mA *(1)Span Calibration Voltage07h 4 ~ 20 mA *(1)Table 15: Calibration voltage of ADAM-5017UHNote: You can substitute 2.5 V for 20 mA if you remove the currentconversion resistor for that channel. However, the calibrationaccuracy will be limited to 0.1% due to the resistor's tolerance.P.36 ADAM-5000 Series I/O Module User’s Manual
I/O Module IntroductionAnalog output module calibrationThe output current of analog output modules can be calibrated by usinga low calibration value and a high calibration value. The analog outputmodules can be configured for one of two ranges: 0-20 mA and 4-20 mA.Since the low limit of the 0-20 mA range (0 mA) is internally an absolutereference (no power or immeasurably small power), just two levels areneeded for calibration: 4 mA and 20 mA.1. Apply power to the ADAM-5000 system including the analog outputmodule for about 30 minutes.2. Assure that the module is correctly installed and that its configurationis according to your specifications and that it matches the output rangeyou want to calibrate. You can do this by using the ADAM utilitysoftware.3. Connect either a 5-digit mA meter or voltmeter with a shunt resistor(250 ohms, .01 % and 10 ppm) to the screw terminals of the module.Figure 26: Output module calibrationADAM-5000 Series I/O Module User’s Manual P.37
Page 1 and 2: ADAM-5000 SeriesI/O ModuleUser's Ma
Page 3 and 4: I/O Module Introduction1. Analog In
Page 5 and 6: Technical specifications of ADAM-50
Page 7 and 8: I/O Module IntroductionCalibration
Page 10 and 11: I/O Module IntroductionTechnical sp
Page 12 and 13: I/O Module IntroductionApplication
Page 14 and 15: I/O Module IntroductionADAM-5017H 8
Page 16 and 17: I/O Module IntroductionFigure 13: L
Page 18 and 19: I/O Module IntroductionVoltageInput
Page 22 and 23: I/O Module IntroductionTechnical sp
Page 26 and 27: I/O Module IntroductionADAM-5018P 7
Page 28 and 29: I/O Module Introduction2. Analog Ou
Page 30 and 31: I/O Module Introduction3. Analog I/
Page 32 and 33: I/O Module Introduction6. CJC Calib
Page 34 and 35: I/O Module IntroductionCalibration
Page 38 and 39: I/O Module Introduction4. Issue the
Page 42 and 43: I/O Module IntroductionADAM-5051(D)
Page 44 and 45: I/O Module IntroductionADAM-5051S 1
Page 46 and 47: I/O Module IntroductionADAM-5052 8-
Page 50 and 51: I/O Module IntroductionADAM-5056(D)
Page 54 and 55: I/O Module IntroductionADAM-5056SO
Page 56 and 57: I/O Module Introduction5. Relay Out
Page 58 and 59: I/O Module IntroductionADAM-5068 re
Page 60 and 61: I/O Module IntroductionADAM-5069 re
Page 62 and 63: I/O Module Introduction6. Counter/F
Page 64 and 65: I/O Module IntroductionADAM-5080 Ap
Page 66 and 67: I/O Module IntroductionFigure 56: W
Page 68 and 69: I/O Module IntroductionSetting Init
Page 70 and 71: Features--Digital Output MappingIf
Page 72 and 73: I/O Module IntroductionADAM-5080 Te
Page 74 and 75: I/O Module IntroductionFigure 56: W
Page 76 and 77: I/O Module IntroductionSetting Init
Page 78 and 79: I/O Module IntroductionFeatures--Di
Page 80 and 81: I/O Module IntroductionADAM-5081 Te
Page 82 and 83: I/O Module IntroductionCommunicatio
Page 84 and 85: I/O Module IntroductionI/O Slots an
Page 86 and 87:
I/O Module Introductionport_set_spe
Page 88:
I/O Module IntroductionTechnical sp
show all

ADAM-5000 Series I/O Module User's Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?