ADAM-5000 Series I/O Module User's Manual

More documents

Recommendations

Info

I/O Module Introduction4. Issue the Analog Data Out command to the module with anoutput value of 4 mA.5. Check the actual output value at the modules terminals. If thisdoes not equal 4 mA, use the "Trim" option in the "Calibrate"submenu to change the actual output. Trim the module until themA meter indicates exactly 4 mA, or in case of a voltage meter withshunt resistor, the meter indicates exactly 1 V. (When calibrating for20 mA using a voltage meter and shunt resistor, the correctvoltage should be 5 V.)6. Issue the 4 mA Calibration command to indicate that the outputis calibrated and to store the calibration parameters in themodule's EEPROM.7. Execute an Analog Data Out command with an output valueof 20 mA. The module's output will be approximately 20 mA.8. Execute the Trim Calibration command as often as necessary untilthe output current is equal to exactly 20 mA.9. Execute the 20 mA Calibration command to indicate that thepresent output is exactly 20 mA. The analog output modulewill store its calibration parameters in the unit's EEPROM.P.38 ADAM-5000 Series I/O Module User’s Manual
I/O Module Introduction4. Digital Input/Output ModulesADAM-5050 16-channel universal digital I/O moduleThe ADAM-5050 features sixteen digital input/output channels.Each channel can be independently configured to be an input oran output channel by the setting of its DIP switch. The digitaloutputs are open collector transistor switches that can becontrolled from the ADAM-5000. The switches can also be used tocontrol solid-state relays, which in turn can control heaters, pumpsand power equipment. The ADAM-5000 can use the module’s digitalinputs to determine the state of limit or safety switches, or to receiveremote digital signals.Warning!A channel may be destroyed if it is subjectedto an input signal while it is configured to bean output channel.ADAM-5050Figure 27: Dip switch setting for digital I/O channelFigure 28: ADAM-5050 module frontal viewADAM-5000 Series I/O Module User’s Manual P.39
Page 1 and 2: ADAM-5000 SeriesI/O ModuleUser's Ma
Page 3 and 4: I/O Module Introduction1. Analog In
Page 5 and 6: Technical specifications of ADAM-50
Page 7 and 8: I/O Module IntroductionCalibration
Page 10 and 11: I/O Module IntroductionTechnical sp
Page 12 and 13: I/O Module IntroductionApplication
Page 14 and 15: I/O Module IntroductionADAM-5017H 8
Page 16 and 17: I/O Module IntroductionFigure 13: L
Page 18 and 19: I/O Module IntroductionVoltageInput
Page 22 and 23: I/O Module IntroductionTechnical sp
Page 26 and 27: I/O Module IntroductionADAM-5018P 7
Page 28 and 29: I/O Module Introduction2. Analog Ou
Page 30 and 31: I/O Module Introduction3. Analog I/
Page 32 and 33: I/O Module Introduction6. CJC Calib
Page 42 and 43: I/O Module IntroductionADAM-5051(D)
Page 44 and 45: I/O Module IntroductionADAM-5051S 1
Page 46 and 47: I/O Module IntroductionADAM-5052 8-
Page 50 and 51: I/O Module IntroductionADAM-5056(D)
Page 54 and 55: I/O Module IntroductionADAM-5056SO
Page 56 and 57: I/O Module Introduction5. Relay Out
Page 58 and 59: I/O Module IntroductionADAM-5068 re
Page 60 and 61: I/O Module IntroductionADAM-5069 re
Page 62 and 63: I/O Module Introduction6. Counter/F
Page 64 and 65: I/O Module IntroductionADAM-5080 Ap
Page 66 and 67: I/O Module IntroductionFigure 56: W
Page 68 and 69: I/O Module IntroductionSetting Init
Page 70 and 71: Features--Digital Output MappingIf
Page 72 and 73: I/O Module IntroductionADAM-5080 Te
Page 74 and 75: I/O Module IntroductionFigure 56: W
Page 76 and 77: I/O Module IntroductionSetting Init
Page 78 and 79: I/O Module IntroductionFeatures--Di
Page 80 and 81: I/O Module IntroductionADAM-5081 Te
Page 82 and 83: I/O Module IntroductionCommunicatio
Page 84 and 85: I/O Module IntroductionI/O Slots an
Page 86 and 87: I/O Module Introductionport_set_spe
Page 88:
I/O Module IntroductionTechnical sp
show all

ADAM-5000 Series I/O Module User's Manual

Create successful ePaper yourself

Delete template?

Save as template?