ARAG Bravo 180 Instructions - Bargam UK

More documents

Recommendations

Info

13.4 Job/spray rate program selection (for automatic control ONLY)Before starting treatment, select the right dosage from those provided in the Menu User (par. 12.1).300 l/ha9.1 Km/h 1) Hold down the key for 1 second toenter the dosage selection menu.12) Press to scroll through the dosagesettings.3) Confirm the selection.If pressure reckoning is ENABLED on spray rate selection,pressure reckoning value and selected nozzle will alternately flash on the display.Rate30
13.5 Automatic treatment controlRefer to Chapter 10 - Computer controls and display - for information on operatingthe keys and switches.300 l/ha 1) Press to enable automatic mode: the letter "A"(automatic) displays.12) Open the section valves by setting the control panelswitches to the up position: their leds will turn on*.3) Drive to the start of the field.4) Set the main control switch up: its led will turn on.6) Run the treatment.*: the leds only turn on for computers configured to operate inP mode. If the computer is configured for M mode, the sectionleds will only turn on when the main control switch is set to ON.4 2When treatment is run in automatic mode, thecomputer keeps delivery to the set value: press thepressure control valve switch to temporarily changethe distribution value: the value can be modified in10% steps (in the range -50% - +50%).This temporarily changes the distribution value:to set a new permanent distribution value, refer topar. 12.1 - Setting the dosage.A) Press to increase the distribution value.B) Press to decrease the distribution value.Attention: when the distribution value is beingchanged, the display alternately flashes the variationpercentage and the current distribution value.To return to the set distribution value, press theRATE key.13.6 Manual treatment controlRefer to Chapter 10 - Computer controls and display - for information on operatingthe keys and switches.300 l/haM11) Press to enable manual mode: the letter "M"(manual) displays.2) Open the section valves by setting the controlpanel switches to the up position: their ledswill turn on*.3) Drive to the start of the field.4) Set the main control switch up: its led will turn on.5) Operate the switch to set the desired dosage.6) Run the treatment.4 25*: the leds only turn on for computers configured to operatein P mode. If the computer is configured for M mode, thesection leds will only turn on when the main control switchis set to ON.31
Page 1 and 2: 02BRAVO 18X SERIES COMPUTERS4671800
Page 3 and 4: Contents• Legend symbols.........
Page 5 and 6: • FOREWORD AND USE OF THIS GUIDET
Page 7 and 8: 5 Contents of the packageThe follow
Page 9 and 10: +Continues par. 6.1 - Recommended s
Page 11 and 12: 7.2 Power connectionInside the pack
Page 13 and 14: 8.3 Connecting the sensors and othe
Page 15 and 16: 10 Computer controls and display10.
Page 17 and 18: 11 Preliminary programmingThe compu
Page 19 and 20: 11.5 LanguageThis parameter sets th
Page 21 and 22: IMPORTANT:BRAVO 18x computers can o
Page 23 and 24: Nozzle type to be matched with spra
Page 25 and 26: 1) When the menuRates setup display
Page 27 and 28: 12.4 Nozzle menuThis menu allows to
Page 29: 13.2 Field selectionWhen treating a
Page 33 and 34: Liquid distributed count300 l/haSpr
Page 35 and 36: 14 Maintenance / diagnostics / repa
Page 37 and 38: Speed sensor input testThe frequenc
Page 39 and 40: 15 Technical data15.1 Units of meas
Page 41 and 42: User menuDatum Min. Max. UM Descrip
Page 43 and 44: Conformity DeclarationARAG s.r.l.Vi

ARAG Bravo 180 Instructions - Bargam UK

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?