Trendsetter NEWS SA - Kodak

More documents

Recommendations

Info

36 Chapter 4 —MaintenanceEdge detection stripDrumFigure 15: Edge detection strip and drumTo clean the edge detection strip:1. Ensure that the output device is not currently imaging plates.2. Shut down the output device.See Shutting Down the <strong>Trendsetter</strong> on page 19.3. Open the front panel.See Opening and Closing the Front and Top Panels on page 31.4. Rotate the drum by hand until the edge detection strip is visible.Figure 15 shows the location of the drum and the edge detection strip.CAUTION: Do not grab the right-end surface of the drum. This candamage the optical encoder in the drum.5. Dampen a cloth (for delicate tasks) with a mixture of 90 percentisopropanol and 10 percent distilled water, and swipe along the striponce, in one direction only.Be careful not to leave any fingerprints or smudges on the strip.
Cleaning the Interior of the Output Device 37Note: Kimwipes® EX-L (Wipers) from Kimberly Clark are recommended forcleaning the edge detection strip.CAUTION: Read and follow all precautions provided by the manufacturerof the isopropanol. Failure to do so can result in personal injury or damageto the output device.6. Close the front panel.See Opening and Closing the Front and Top Panels on page 31.Cleaning the Plate RollerClean the plate roller monthly.Plate rollerDrumFigure 16: Plate roller and drumCAUTION: Never put any pressure on or bend the plate rollers. Doing somay damage the plate rollers.
Page 1: Operator GuideEnglishTrendsetter NE
Page 5 and 6: CopyrightCopyright © 2004 Creo Inc
Page 7 and 8: Contents1 Safety 1Who Should Use Th
Page 9 and 10: ContentsviiGeneral Safety Labels ..
Page 11 and 12: SafetyWho Should Use This Guide....
Page 13 and 14: Important Notes on Safe Operation 3
Page 15 and 16: Safety Features 5InstallationMainte
Page 17 and 18: Safety Features 7Emergency Stop Swi
Page 19 and 20: System OverviewTrendsetter NEWS SA
Page 21 and 22: Output Device 11Output DeviceThis g
Page 23 and 24: Trendsetter NEWS SA Components 13Ta
Page 25 and 26: Supported Plates 15ItemPlatesDescri
Page 27 and 28: OperationStarting the Trendsetter..
Page 29: Shutting Down the Trendsetter 19Shu
Page 32 and 33: 22 Chapter 3 —Operation7. Align t
Page 34 and 35: 24 Chapter 3 —Operation
Page 36 and 37: 26 Chapter 4 —MaintenanceMaintena
Page 38 and 39: 28 Chapter 4 —MaintenanceFor Your
Page 40 and 41: 30 Chapter 4 —MaintenanceAccessin
Page 42 and 43: 32 Chapter 4 —Maintenance3. Lift
Page 44 and 45: 34 Chapter 4 —MaintenanceTo repla
Page 48 and 49: 38 Chapter 4 —MaintenanceTo clean
Page 50 and 51: 40 Chapter 4 —MaintenanceInspect
Page 52 and 53: 42 Chapter 4 —MaintenanceReplacin
Page 54 and 55: 44 Chapter 4 —Maintenance12. Pull
Page 56 and 57: 46 Chapter 4 —MaintenanceReplacem
Page 58 and 59: 48 Chapter 4 —Maintenance
Page 60 and 61: 50 Chapter 5 —TroubleshootingOper
Page 62 and 63: 52 Chapter 5 —TroubleshootingUp t
Page 64 and 65: 54 Chapter 5 —TroubleshootingErro
Page 66 and 67: 56 Chapter 5 —TroubleshootingTabl
Page 68 and 69: 58 Chapter 5 —TroubleshootingNume
Page 78 and 79: 68 Chapter 5 —TroubleshootingRemo
Page 80 and 81: 70 Chapter 5 —Troubleshooting4. R
Page 86 and 87: 76 Appendix A —Part NumbersParts
Page 88 and 89: 78 Appendix B —LabelsOverviewThis
Page 90 and 91: 80 Appendix B —LabelsIdentificati
Page 92 and 93: 82 Appendix B —LabelsFCC Certific
Page 94 and 95: 84 Appendix B —LabelsMoving Parts
Page 96 and 97:
86 Appendix B —LabelsGeneral Safe
Page 98 and 99:
88 Appendix B —LabelsKeep Hands O
Page 100 and 101:
90 Appendix B —LabelsStrong Magne
Page 102 and 103:
92 Appendix C —Regulatory Complia
Page 104 and 105:
94 Appendix C —Regulatory Complia
Page 106 and 107:
96 Trendsetter NEWS SA Operator Gui
Page 108 and 109:
98 Trendsetter NEWS SA Operator Gui
Page 110 and 111:
100 Trendsetter NEWS SA Operator Gu
Page 112:
102 Trendsetter NEWS SA Operator Gu
show all

Trendsetter NEWS SA - Kodak

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?