Smart Programmer - UK

More documents

Recommendations

Info

1Contents of thepackage2PresentationSEKOSMART- Programmer- Laundry system4.4 Automation MenuFrom the Parameters Menu, select “AUT” or press [1]; the following message will appear on thedisplay:AUTomationsDOS DES SOF3INItialize theprogrammer4Entering theparameters• Setting theflushing function• Drainagesolenoid valve• Filtering of inputsignals• Automationmenu5Programming6Programming theMemory Card7Examples ofprogramming8Switching theprogrammer onand off9Connecting theprogrammer to aPC or to theConsole4.4.1 Dosage AutomationTo set automation of the metering function, that is to say the possibility of assigning the metering valuesdirectly in grams rather than in seconds, avoiding the need for troublesome calculations, it is necessaryfirst of all to carry out the CALIBRATION of the pumps, proceeding as follows: WARNING: Close the water-delivery valve before carrying out the operations describedbelow. This will avoid DANGEROUS spillage of water or of products, or reduce them to aminimum. While the pumps are running, the solenoid valve opens and remains open for thetime set under AUT (see point 4.1).• From the control console, enter the PUMP PRIMING mode. Consult the SMART systemmanual (point 3.2.5).• Use [SEL] to select the pump to be calibrated.• Have a graduated container available in which to collect the product being metered. To do this,it is necessary to disconnect the delivery tube from the pumps by exerting pressure on themetal spring with a pair of pliers. WARNING: Remember to close the valve.• Press [START] to start the pump that has been selected. It will stop automatically after 10seconds.• Multiply the obtained cm 3 by the product density (e.g. 200 cm 3 dosed product ⇒ 200 cm 3x 1.1 g/cm 3 (density) = 220 grams /10 seconds) or weigh the product with a scale.• Note this information on the PROGRAMS sheet, in the appropriate place.• Repeat the above operations from point 2 for each pump in the system.Upon completion of the operation for checking the metering carried out by the pumps, press the [SEL]key and hold it down for over 3 seconds to return to the PROGRAM SELECTION mode.At this point it is possible to enter the data just acquired.• From the Automation menu, select “DOS” or press [1]; the following message will appear onthe display:DOSage autom.Pump 0 0000• Enter the number of the pump in the place of the “0” and confirm by pressing [Enter];• Enter the datum obtained from the CALIBRATION of the pump in the place of the “0000” andconfirm by pressing [Enter].• Repeat from point 1 for each pump.Press [ESC] to return to the Automation menu.A pump for which a calibration datum other than 0000 has been entered will run for a period of timecalculated automatically by the system.Instruction 6: PUMP 0¹0000²s 0000³sr will be altered in PUMP 0¹0000²g 0000³sr.Smart programmer Version 3.0 Code n° 0000136346 10
SEKOSMART- Programmer- Laundry system1Contents of thepackage2Presentation3INItialize theprogrammer4.4.2 Destainer AutomationIt is possible to carry out metering of the destainer only if the operator has enabled metering by meansof the appropriate key on the control console (see point 3.4 in the SMART System manual). WARNING: This key will enable the destainer pump to meter the product only for thewashing cycle that is about to take place. If the LED is on and the pump is running, furthermetering can be avoided by pressing the key. The LED will extinguish. If metering is currentlytaking place, it will not be stopped.• From the automation menu, select “DES”; the following message will appear on the display:4Entering theparameters• Setting theflushing function• Drainagesolenoid valve• Filtering of inputsignals• Automationmenu5Programming6Programming theMemory Card7Examples ofprogramming• By entering the number of the pump that will meter the destainer and then pressing [Enter] toconfirm, the DESTAINER key on the control console is enabled. The pump will only be able torun if the relevant LED is illuminated.• If 0 (the default value) is entered, the key will not have any function, the LED will always remainoff and the destainer pump will behave in the same way as the other pumps.4.4.3 Softner AutomationDEStainerPump 0autom.The principles indicated for destainer also apply to the softner. Proceed as already indicated forautomation of the softner function.From the Automation menu, select “SOF” or press [3]; the following message will appear on the display:SOFtner autom.Pump 08Switching theprogrammer onand off9Connecting theprogrammer to aPC or to theConsoleSmart programmer Version 3.0 Code n° 0000136346 11
Page 2 and 3: SEKOSMART- Programmer- Laundry syst
Page 8 and 9: 1Contents of thepackage2Presentatio
Page 24: SEKOSMART- Programmer- Laundry syst

Smart Programmer - UK

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?