Smart Programmer - UK

More documents

Recommendations

Info

SEKOSMART- Programmer- Laundry system1Contents of thepackage2Presentation3INItialize theprogrammer4Entering theparameters5Programming• Programminginstructions• Programmingeditor6Programming theMemory Card7Examples ofprogramming8Switching theprogrammer on andoff9Connecting theprogrammer to a PCor to the ConsoleInstruction 6: PUMP 0¹0000²s/g 0000³sr0¹ replace with pump n° 1 to 80000² replace with 0 to 255 (seconds) if the letter “s” is shown0 to 9999 (grams) if the letter “g” is shown (see point 4.4.1)0000³ replace with 0 to 2000 (seconds of delay).The system starts pump number 0¹, for 0000² seconds or until it has metered a quantity of product ingrams, then it goes on to the instruction in the next line (the system recognises the settingautomatically, and after 0000² it displays an s to indicate that the metering is in seconds or a g toindicate that the metering is in grams (see the MET parameter under point 4.4.1). The numbers 0000³srindicate the delay with which the pump has to start. WARNING: If more than one consecutive line is written with this instruction, they areexecuted at the same time, however the lines from the fourth onwards are not consideredsince it is not possible for more than three pumps to run at the same time!Example: 150 grams are required to be metered by pump 4 with a delay of 30 seconds. To do this, it isnecessary to make sure that CALIBRATION of PUMP 4 has been carried out and that thedatum has been entered under MET (see point 4.4.1).The instruction will be: PUMP 4 0150g 0030srInstruction 7: REPEAT 0¹ (replace the variable 0¹ with 1 to 6)REPEAT 0: The system skips to line 00. In practice it starts off again from the first instruction in theprogram. If the [DEST] (destainer) and [SOFT] (softener) keys have been enabled andactivated (see point 4.4.2/4.4.3 ), these will be de-activated and the associated LEDS willextinguish. Press the [DEST] (destainer) and/or [SOFT] (softener) keys again if you wishto enable metering during the next wash.The statistics counter for the program will not be incremented.REPEAT 1: The system skips to line 00. In practice it starts off again from the first instruction in theprogram. If the [DEST] (destainer) and/or [SOFT] (softener) keys have been enabled andactivated (see point 4.4.2/4.4.3 ), these will be de-activated and the associated LEDS willextinguish. Press the [DEST] (destainer) and/or [SOFT] (softener) keys again if you wishto enable metering during the next wash.The statistics counter for the program will be incremented.Example: It is possible to repeat the same program without having to select it each time. At the end ofthe program, enter the instruction REPEAT, which will replace END.Instruction 8: S-1 0¹ 00²replace the variables 0¹ with 1...6 (input signal)replace the variables 00² with 00…24 (programming line)The system checks but does not wait for the signal 0¹. If acknowledgement of the signal 0¹ doesnot take place, the system continues with the instruction on the next line, otherwise control passesto program line 00².N.B.: The instruction does not wait for the signal 0¹ to become active and simply monitors it. This meansthat execution of the program does not stop at this instruction but in any case follows one of the twopossible alternatives, that is to say either the next instruction or the instruction on line 00².Instruction 0: ENDSmart programmer Version 3.0 Code n° 0000136346 14
SEKOSMART- Programmer- Laundry systemThis instruction ends the wash program. Two dashes - - will appear on the control console. Thestatistics counter for the program will be incremented.Smart programmer Version 3.0 Code n° 0000136346 15
Page 2 and 3: SEKOSMART- Programmer- Laundry syst
Page 8 and 9: 1Contents of thepackage2Presentatio
Page 10 and 11: 1Contents of thepackage2Presentatio
Page 24: SEKOSMART- Programmer- Laundry syst

Smart Programmer - UK

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?