3160 - Trace oxygen analyzer - Teledyne Analytical Instruments

More documents

Recommendations

Info

3 InstallationFigure 3-4: Removing the Voltage Card4. Turn the card so that the desired voltage can be read at the bottom.5. Slide the indicator pin around the card so that it is pointing up when thevoltage is read at the bottom (see Figure 3–5).Figure 3–5: Voltage Selection6. Place the voltage selector card back into the housing. The edge where thedesired voltage is printed should go in first and the printed side of the cardshould be facing the IEC connector.7. Replace the fuse block and the cover. Verify that the indicator pin ispointing to the correct voltage.3.6.2 Fuse ChangingNOTE: Spare fuses are located in a clip attached to the power supply enclosureinside of the <strong>analyzer</strong>.3-8TELEDYNE ANALYTICAL INSTRUMENTS
Installation 3WARNING: Power cord must be disconnected before performing anyvoltage selection!To change from North American to European fuses, perform the following:1. Use a small blade screwdriver to open the cover.2. Loosen the Phillips screw two turns and remove the fuse block by sliding itaway from the screw and up from the pedestal.3. Remove the North American fuse and turn the fuse block over.4. Replace the fuse with European fuses. Two European fuses are required,but the lower one may be replaced with a dummy fuse, or jumper bar (seeFigure 3–6).European 1.6 Amp T Fuses5 x 20 mmNorth American 3 A T FusesFigure 3–6: Fuse Replacement5. Slide the fuse block back on the Phillips screw and pedestal.6. Tighten the Phillips screw and replace the cover.NOTE: The fuses that go into the housing first are the active set.TELEDYNE ANALYTICAL INSTRUMENTS3-9
Page 3 and 4: TELEDYNE ANALYTICAL INSTRUMENTSiii
Page 5 and 6: Tabable of Contents (continued)Cali
Page 7 and 8: Introduction 1Introduction1.1 Featu
Page 9 and 10: Introduction 11.2 ComponentsThe ana
Page 11 and 12: Operational Theory 2Operational The
Page 13 and 14: Operational Theory 22.1.1 Micro-Fue
Page 15 and 16: Operational Theory 2to be used to z
Page 17 and 18: Operational Theory 2The analog outp
Page 19 and 20: Installation 3InstallationInstallat
Page 21 and 22: Installation 3DIMENSIONS:InmmREMOVA
Page 23 and 24: Installation 33.5 Micro-Fuel Cell S
Page 25: Installation 3Figure 3-3: 3160 Rear
Page 29 and 30: Operations 4Operations4.1 Front Pan
Page 31 and 32: Operations 4When waiting for manual
Page 33 and 34: Operations 4Cold Start-Up1. A cold
Page 35 and 36: Operations 47. If the O 2cell curre
Page 37 and 38: Operations 47. If AUTO was chosen i
Page 39 and 40: Operations 4Select Active Sensor (T
Page 41 and 42: Operations 47. After pressing ACK i
Page 43 and 44: Operations 4Set-Up Alarms1. Enter s
Page 45 and 46: Logger Set-Up1. Enter set-up from t
Page 47 and 48: Set-Up Clock Functions1. Enter set-
Page 49 and 50: Changing Passwords for Remote Monit
Page 51 and 52: Operations 4System Statistics1. Ent
Page 53 and 54: Operations 412. After checking for
Page 55 and 56: Maintenance & Trouboubleshooting 5M
Page 57 and 58: Maintenance & Trouboubleshooting 5S
Page 59 and 60: AppendixAppendixA.1 Specifications(
Page 61 and 62: AppendixA.2 Recommended Spare Parts
Page 63 and 64: AppendixSection IV - Fire and Explo
Page 65 and 66: AppendixEye Protection:Hand Protect
Page 67 and 68: AppendixSection III - Physical Haza

3160 - Trace oxygen analyzer - Teledyne Analytical Instruments

Create successful ePaper yourself

Delete template?

Save as template?