3160 - Trace oxygen analyzer - Teledyne Analytical Instruments

More documents

Recommendations

Info

4 OperationsCalibration Zeroing1. At the main Analyze mode screen press ZERO.2. Press ACK to acknowledge that a low O 2gas has alreadybeen connected to the sample port. The samplegas O 2level should be close to zero to preserve the lifeof the scrubber (if one is installed).3. Set the flow rate to 2 SCFH using the knob on the systemfront panel and press ACK.4. Press AUTO to let the system determine the settlingtime before spanning or press MAN for manual.5. If MAN was chosen in step 4, watch the logger or theO 2value on the screen to assess when the output is constant,and then press ACK.6. After step 5, the system will automatically span to theuser-entered span value. If the zeroing is successful, themain Analyze mode menu will appear as in step 10.4-6TELEDYNE ANALYTICAL INSTRUMENTS
Operations 47. If the O 2cell current is too large to be zeroed, an errormessage will appear. Press ACK to retry or ESC toabort the zeroing process.8. If AUTO was chosen in step 4, wait for the O 2level tosettle before the system zeros. This may take from thirty(30) seconds to fifteen (15) minutes, depending on thesample gas <strong>oxygen</strong> level.9. After a stable low <strong>oxygen</strong> level is detected by the system,the system will automatically zero.If the O 2cell current is too large to be zeroed, an errormessage will appear (see step 7). You will then have topress ESC to abort, or ACK to retry.10. If the zero is successful, the system will return to themain Analyzer mode menu.TELEDYNE ANALYTICAL INSTRUMENTS4-7
Page 3 and 4: TELEDYNE ANALYTICAL INSTRUMENTSiii
Page 5 and 6: Tabable of Contents (continued)Cali
Page 7 and 8: Introduction 1Introduction1.1 Featu
Page 9 and 10: Introduction 11.2 ComponentsThe ana
Page 11 and 12: Operational Theory 2Operational The
Page 13 and 14: Operational Theory 22.1.1 Micro-Fue
Page 15 and 16: Operational Theory 2to be used to z
Page 17 and 18: Operational Theory 2The analog outp
Page 19 and 20: Installation 3InstallationInstallat
Page 21 and 22: Installation 3DIMENSIONS:InmmREMOVA
Page 23 and 24: Installation 33.5 Micro-Fuel Cell S
Page 25 and 26: Installation 3Figure 3-3: 3160 Rear
Page 27 and 28: Installation 3WARNING: Power cord m
Page 29 and 30: Operations 4Operations4.1 Front Pan
Page 31 and 32: Operations 4When waiting for manual
Page 33: Operations 4Cold Start-Up1. A cold
Page 37 and 38: Operations 47. If AUTO was chosen i
Page 39 and 40: Operations 4Select Active Sensor (T
Page 41 and 42: Operations 47. After pressing ACK i
Page 43 and 44: Operations 4Set-Up Alarms1. Enter s
Page 45 and 46: Logger Set-Up1. Enter set-up from t
Page 47 and 48: Set-Up Clock Functions1. Enter set-
Page 49 and 50: Changing Passwords for Remote Monit
Page 51 and 52: Operations 4System Statistics1. Ent
Page 53 and 54: Operations 412. After checking for
Page 55 and 56: Maintenance & Trouboubleshooting 5M
Page 57 and 58: Maintenance & Trouboubleshooting 5S
Page 59 and 60: AppendixAppendixA.1 Specifications(
Page 61 and 62: AppendixA.2 Recommended Spare Parts
Page 63 and 64: AppendixSection IV - Fire and Explo
Page 65 and 66: AppendixEye Protection:Hand Protect
Page 67 and 68: AppendixSection III - Physical Haza

3160 - Trace oxygen analyzer - Teledyne Analytical Instruments

Create successful ePaper yourself

Delete template?

Save as template?