3160 - Trace oxygen analyzer - Teledyne Analytical Instruments

More documents

Recommendations

Info

4 OperationsInstall Sensor and Test Alternate Sensor (Two Cells Only)1. Enter set-up from the Analyze mode by pressingSETUP.If only one cell is installed, the TEST and INSTL optionson the next screen are omitted.2. Press TEST to test the alternate sensor or INSTL to installa new sensor.3. If TEST was chosen in step 2, the active sensor is displayedand you are directed to press ACK to test the alternatesensor.If INSTL was chosen in step 2, go to step 5.4. After pressing ACK in step 3, the alternate sensor isflushed for 10 minutes while the measured O 2level isdisplayed. The 10 minute flush may be restarted bypressing RESET, or aborted by pressing SKIP. Go tostep 8.5. If INSTL was chosen in step 3, the screen will displaythe active sensor. Press A or B for the sensor you areinstalling.6. Install the sensor (either A or B from step 5) into thesensor block within two minutes, and press ACK.4-12TELEDYNE ANALYTICAL INSTRUMENTS
Operations 47. After pressing ACK in step 6, the new sensor is flushedfor 10 minutes while the measured O 2level is displayed.The 10-minute flush may be restarted by pressing RE-SET, or aborted by pressing SKIP.8. When sensor installation or alternate sensor test arecomplete, the system will return to the main Analyzemode menu.TELEDYNE ANALYTICAL INSTRUMENTS4-13
Page 3 and 4: TELEDYNE ANALYTICAL INSTRUMENTSiii
Page 5 and 6: Tabable of Contents (continued)Cali
Page 7 and 8: Introduction 1Introduction1.1 Featu
Page 9 and 10: Introduction 11.2 ComponentsThe ana
Page 11 and 12: Operational Theory 2Operational The
Page 13 and 14: Operational Theory 22.1.1 Micro-Fue
Page 15 and 16: Operational Theory 2to be used to z
Page 17 and 18: Operational Theory 2The analog outp
Page 19 and 20: Installation 3InstallationInstallat
Page 21 and 22: Installation 3DIMENSIONS:InmmREMOVA
Page 23 and 24: Installation 33.5 Micro-Fuel Cell S
Page 25 and 26: Installation 3Figure 3-3: 3160 Rear
Page 27 and 28: Installation 3WARNING: Power cord m
Page 29 and 30: Operations 4Operations4.1 Front Pan
Page 31 and 32: Operations 4When waiting for manual
Page 33 and 34: Operations 4Cold Start-Up1. A cold
Page 35 and 36: Operations 47. If the O 2cell curre
Page 37 and 38: Operations 47. If AUTO was chosen i
Page 39: Operations 4Select Active Sensor (T
Page 43 and 44: Operations 4Set-Up Alarms1. Enter s
Page 45 and 46: Logger Set-Up1. Enter set-up from t
Page 47 and 48: Set-Up Clock Functions1. Enter set-
Page 49 and 50: Changing Passwords for Remote Monit
Page 51 and 52: Operations 4System Statistics1. Ent
Page 53 and 54: Operations 412. After checking for
Page 55 and 56: Maintenance & Trouboubleshooting 5M
Page 57 and 58: Maintenance & Trouboubleshooting 5S
Page 59 and 60: AppendixAppendixA.1 Specifications(
Page 61 and 62: AppendixA.2 Recommended Spare Parts
Page 63 and 64: AppendixSection IV - Fire and Explo
Page 65 and 66: AppendixEye Protection:Hand Protect
Page 67 and 68: AppendixSection III - Physical Haza

3160 - Trace oxygen analyzer - Teledyne Analytical Instruments

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?