Determination of Creep Compliance and Tensile Strength of Hot-Mix ...

More documents

Recommendations

Info

0.060.05Creep Compliance (1/GPa)0.040.030.020.010.000 20 40 60 80 100 120Time (sec)0.07'06-84 06-101 06-125 06-150Figure A-23: 4 Mixes @ 4% Voids & -20°C0.060.05Creep Compliance (1/GPa)0.040.030.020.010.000 20 40 60 80 100 120Time (sec)'06-84 06-101 06-125 06-150 07-123 06-105Figure A-24: 6 Mixes @ 6.5% Voids & -20°CB
0.080.070.06Creep Compliance (1/GPa)0.050.040.030.020.010.000 20 40 60 80 100 120Time (sec)0.09'06-84 06-101 06-125 06-150Figure A-25: 4 Mixes @ 9% Voids & -20°C0.080.07Creep Compliance (1/GPa)0.060.050.040.030.020.010.000 20 40 60 80 100Time (sec)120'06-84 06-101 06-125 06-150Figure A-26: 4 Mixes @ 4% Voids & -10°CC
Page 1 and 2:
• • • • • • • • •
Page 3 and 4: TECHNICAL REPORT DOCUMENTATION PAGE
Page 5 and 6: TABLE OF CONTENTSACKNOWLEDGEMENTS .
Page 7 and 8: LIST OF FIGURESFigure 1: Test Equip
Page 9 and 10: LIST OF TABLESTable 1: HMA Mixes an
Page 11 and 12: OBJECTIVESThe objective of this pro
Page 13 and 14: voids generally describes the avera
Page 15 and 16: Figure 1: Test Equipment SetupCreep
Page 17 and 18: and level of % air voids. Although
Page 19 and 20: specimen is actually at the test te
Page 21 and 22: same four mixes but at 4.4°C (40°
Page 23 and 24: n Dn PNormalization Constant = ×
Page 25 and 26: where:0.05 ≤ ν ≤ 0.50Tensile S
Page 27 and 28: Table 4: Creep Compliance: 06-101 (
Page 29 and 30: 0.10Creep Compliance (1/GPa)07-123
Page 31 and 32: as it pertains to creep compliance,
Page 33 and 34: However, published documentation of
Page 35 and 36: Getting back to the issue of the er
Page 37 and 38: 0.090Creep Compliance @ 100 sec. @
Page 39 and 40: Table 12: Instrumented Tensile Stre
Page 41 and 42: Table 15: All Tensile Strength: -10
Page 43 and 44: 100090080006-101Virgin binder = PG7
Page 45 and 46: Tensile Failure StrainThe tensile f
Page 47 and 48: Table 18: Tensile Failure Strain: -
Page 49 and 50: CONCLUSIONSExpected trends such as
Page 51 and 52: REFERENCES1. Guide for Mechanistic-
Page 53: APPENDIX A: CREEP COMPLIANCE
Page 57 and 58: 0.200.180.160.14Creep Compliance (1
Page 59 and 60: 0.180.160.14Creep Compliance (1/GPa
Page 61 and 62: 0.160.140.12Creep Compliance (1/GPa
Page 63 and 64: 0.300.25Creep Compliance (1/GPa)0.2
Page 65 and 66: 0.140.12Creep Compliance (1/GPa)0.1
Page 67 and 68: Table B-19: Non-instrumented Data @
Page 69 and 70: Table B-21: Instrumented Data @ 21.
Page 71 and 72: Table B-23: Instrumented Data @ 4.4
Page 73 and 74: Table B-25: Instrumented Data @ -10
show all

Determination of Creep Compliance and Tensile Strength of Hot-Mix ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?