Determination of Creep Compliance and Tensile Strength of Hot-Mix ...

More documents

Recommendations

Info

0.200.180.16Creep Compliance (1/GPa)0.140.120.100.080.0606-150: 6.5% Voids0.040.020.000 20 40 60 80 100 120Time (sec)-20 DegC -10 DegC 0 DegC0.30Figure A-43: 06-150 @ 6.5% Voids0.25Creep Compliance (1/GPa)0.200.150.1006-150: 9% Voids0.050.000 20 40 60 80 100Time (sec)120-20 DegC -10 DegC 0 DegCFigure A-44: 06-150 @ 9% VoidsL
0.140.12Creep Compliance (1/GPa)0.100.080.060.0406-105: 6.5% Voids0.020.000 20 40 60 80 100 120Time (sec)-20 DegC -10 DegC 0 DegCFigure A-45: 06-105 @ 6.5% VoidsM
Page 1 and 2:
• • • • • • • • •
Page 3 and 4:
TECHNICAL REPORT DOCUMENTATION PAGE
Page 5 and 6:
TABLE OF CONTENTSACKNOWLEDGEMENTS .
Page 7 and 8:
LIST OF FIGURESFigure 1: Test Equip
Page 9 and 10:
LIST OF TABLESTable 1: HMA Mixes an
Page 11 and 12:
OBJECTIVESThe objective of this pro
Page 13 and 14: voids generally describes the avera
Page 15 and 16: Figure 1: Test Equipment SetupCreep
Page 17 and 18: and level of % air voids. Although
Page 19 and 20: specimen is actually at the test te
Page 21 and 22: same four mixes but at 4.4°C (40°
Page 23 and 24: n Dn PNormalization Constant = ×
Page 25 and 26: where:0.05 ≤ ν ≤ 0.50Tensile S
Page 27 and 28: Table 4: Creep Compliance: 06-101 (
Page 29 and 30: 0.10Creep Compliance (1/GPa)07-123
Page 31 and 32: as it pertains to creep compliance,
Page 33 and 34: However, published documentation of
Page 35 and 36: Getting back to the issue of the er
Page 37 and 38: 0.090Creep Compliance @ 100 sec. @
Page 39 and 40: Table 12: Instrumented Tensile Stre
Page 41 and 42: Table 15: All Tensile Strength: -10
Page 43 and 44: 100090080006-101Virgin binder = PG7
Page 45 and 46: Tensile Failure StrainThe tensile f
Page 47 and 48: Table 18: Tensile Failure Strain: -
Page 49 and 50: CONCLUSIONSExpected trends such as
Page 51 and 52: REFERENCES1. Guide for Mechanistic-
Page 53 and 54: APPENDIX A: CREEP COMPLIANCE
Page 55 and 56: 0.080.070.06Creep Compliance (1/GPa
Page 57 and 58: 0.200.180.160.14Creep Compliance (1
Page 63: 0.300.25Creep Compliance (1/GPa)0.2
Page 67 and 68: Table B-19: Non-instrumented Data @
Page 69 and 70: Table B-21: Instrumented Data @ 21.
Page 71 and 72: Table B-23: Instrumented Data @ 4.4
Page 73 and 74: Table B-25: Instrumented Data @ -10
show all

Determination of Creep Compliance and Tensile Strength of Hot-Mix ...

Create successful ePaper yourself

Delete template?

Save as template?