Dimensional Metrology - Procontrol AMC

More documents

Recommendations

Info

pin gaugesThread Measuring Wires with handle and needle's eye401–Steel, tolerance 0Specification Hardened, aged, groundand lapped.Diameter 0.10–10.00 mmManuf. tolerance ± 0.0003 mm402–Steel, tolerance 1Specification Hardened, aged, groundand lapped.Diameter 0.10–10.00 mmManuf. tolerance ± 0.001 mmArt. no. Type Diameter, mm Length, mm401-0,10-0,19 401 0.10–0.19 32401-0,20-0,29 401 0.20–0.29 32401-0,30-0,49 401 0.30–0.49 32401-0,50-0,99 401 0.50–0.99 32401-1,00-2,99 401 1.00–2.99 32401-3,00-5,99 401 3,00 - 5,99 32401-6,00-10,00 401 6.00–10.00 32Art. no. Type Diameter, mm Length, mm402-0,10-0,19 402 0.10–0.19 32402-0,20-0,29 402 0.20–0.29 32402-0,30-0,49 402 0.30–0.49 32402-0,50-0,99 402 0.50–0.99 32402-1,00-2,99 402 1.00–2.99 32402-3,00-5,99 402 3.00–5.99 32402-6,00-10,00 402 6.00–10.00 32Thread Measuring Wires with Micrometer HolderArt. no. Type Diameter, mm501-0,15-1,00 * 501 0.15–1.00501-1,00-3,20 * 501 1.00–3.20501-3,20-6,50 * 501 3.20–6.50501-0,170 501 0.170501-0,195 501 0.195501–Steel: Set of three Measuring Wires in two holdersSpecification Hardened, aged, ground and lapped.Diameter0.10–10.00 mmManuf. tolerance ± 0.001 mmMicrometer holder Available for micrometers with spindlediameter: 6.35 - 6.50 - 6.80 - 7.50 and 8.00 mmSpecial diameters must be stated when ordering orwhen making an enquiry.The following diameters from the “Zeiss-series” areavailable for spindle diameters 6.35 - 6.50 and 8.00 mm.0.17 0.195 0.22 0.25 0.290.335 0.39 0.455 0.53 0.620.725 0.895 1.10 1.35 1.652.05 2.55 3.20 mmOther wire diameters and spindle diameters are available on request.The Thread Measuring Wires are also available in carbide or ceramics onrequest.* When ordering, please state diameter needed (e.g. 0.328 mm).Available in steps of 0.001 mm.501-0,220 501 0.220501-0,250 501 0.250501-0,290 501 0.290501-0,335 501 0.335501-0,390 501 0.390501-0,455 501 0.455501-0.530 501 0.530501-0,620 501 0.620501-0,725 501 0.725501-0,895 501 0.895501-1,100 501 1.100501-1,350 501 1.350501-1,650 501 1.650501-2,050 501 2.050501-2,550 501 2.550501-3,200 501 3.200501-4,000 501 4.000501-5,050 501 5.050501-6,350 501 6.35058Contact us at info@cej.se • Phone +46 (0) 16 15 06 40 • Fax +46 (0) 16 15 06 59
unimeterOriginal UnimeterUNIMETER is robust, flexible and easy to handle. UNIMETER consists of a precision cylinder on which two measuring jaws are placed.The upper front jaw is movable when measuring, and its movement is free from play and friction. The deflection of this movable jaw istransferred to an indicator, normally a dial gauge or a mikrokator.The lower measuring jaw, which is fixed when measuring, is adjustable along the cylinder and can be secured at an optional distance fromthe upper jaw.UNIMETER is set by means of gauge blocks, reference rings or similar to the required gauge size. The rear jaw is secured in a suitable position.After setting the indicator to zero, the Unimeter is ready for use. UNIMETER measuring range can be increased by extension bars, and it caneasily be adapted for unique applications.Type UNI I – for internal measurementType I – For internal measurementMeasuring jaws with parallel, cylindricalmeasuring surfaces. Without indicator and caseTypeOrder no.UNI-2I 8828-01002UNI-2LI 8828-01003UNI-2ELI 8828-01004CasesDescriptionOrder no.Case for I 8828-01005Case for LI 8828-01006Case for ELI 8828-01007Technical data UNI-2I UNI-2LI UNI-2ELIRange of application, mm 28–247 28–347 28–447Measuring movement, mm * 3.0 3.0 3.0Measuring depth, mm 32 32 32* Max. movement of the measuring jaw, in mmType UNI O – for external measurementType O – For external measurementMeasuring jaws with parallel, flat measuringsurfaces. For measuring length, externaldiameter, tooth thickness, etc.Without indicator and caseTypeOrder no.UNI-2O 8828-01012UNI-2LO 8828-01013UNI-2ELO 8828-01014CasesDescriptionOrder no.Case for O 8828-01005Case for LO 8828-01006Case for ELO 8828-01007Technical Data UNI-2O UNI-2LO UNI-2ELORange of application, mm 0–220 0–320 0–420Measuring movement, mm * 3.0 3.0 3.0Measuring depth, mm 35 35 35For gears with min. module 1.5 1.5 1.5Guideline max. modul 1) 25 1) 25 1) 25Guideline max. D at module 10 620 750 750* Max. movement of the measuring jaw, in mm1) At "D" max. 300 mm.Contact us at info@cej.se • Phone +46 (0) 16 15 06 40 • Fax +46 (0) 16 15 06 59 59
Page 1 and 2:
c e j o h a n s s o n a bDimensiona
Page 3 and 4:
mikrokators and accessoriesCEJ Mikr
Page 5 and 6:
mikrokators and accessoriesCEJ Mikr
Page 7 and 8:
dial gaugesCEJ Dial GaugesDial Gaug
Page 10 and 11: indicator standIndicator StandIndic
Page 12 and 13: inside micrometersCEJ Inside Microm
Page 14 and 15: multigauging fixturesCombicheckComb
Page 16 and 17: multigauging fixturesCombicheck Sta
Page 18 and 19: multigauging fixturesCombifixCombif
Page 20 and 21: multigauging fixturesAccessoriesCEJ
Page 22 and 23: multigauging fixturesRocker w. Ball
Page 24 and 25: multigauging fixturesUD-Universal M
Page 26 and 27: depth measuring gaugeCEJ Depth Meas
Page 28 and 29: metemCEJ Metem Electronic Measuring
Page 30 and 31: metemMetem 2000Metem 2000 Display U
Page 32 and 33: metemContact tips for narrow spaces
Page 34 and 35: metemPROBE HEAD-PNEUMATIC AND VACUU
Page 36 and 37: metemMetem Digital ProbesMetem digi
Page 38 and 39: metemSYSTEM ACCURACYAll accuracies
Page 40 and 41: metemMetem Gauging probesMetem gaug
Page 42 and 43: metemPROBE HEADSpring pushPneumatic
Page 45 and 46: diaclean and gauge block holderDiac
Page 47 and 48: fixed gauges for plain bores and sh
Page 53 and 54: screw gauges for threaded bores and
Page 59: pin gaugesPin Gauges with handle101
Page 63 and 64: unimeterType UNI M - With interchan
Page 65 and 66: ativaATIVA-GaugeA system for gauge
Page 68: CE Johansson ABEskilstuna, Swedente
show all

Dimensional Metrology - Procontrol AMC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?