E110 FIREYE FLAME-MONITOR™ - Westmill Industries

More documents

Recommendations

Info

SYSTEM INFO The sub-menu “SYSTEM INFO” allows the user to review information pertaining to the operation of the control (e.g. average main flame signal strength, status of the high fire and low fire end switches, etc.). This information can be very helpful when setting the damper linkages on the firing rate motor. The MODE key is used to enter the “PROGRAM SETUP” sub-menu, and the SCRL key is used to advance through the sub-menu. Press Screen Displays Description SCRL AUTO 45 SCRL key advances through the historical information until SYSTEM INFO > “System Info” is displayed. Control has released to auto modulation, flame signal strength = 45. MODE AUTO 45 The average flame signal strength of the pilot flame = 22 AVG. PILOT FLM 22 SCRL AUTO 45 The average flame signal strength of the main flame = 40. AVG. MAIN FLM 40 SCRL AUTO 45 The total number of short circuits (excessive current) detected on SHORT CKTS. 0 terminals 5, 6, and 7. The short circuit condition must be sensed twice consecutively to be considered a short circuit. SCRL AUTO 45 The status of the high fire end switch (D-8) is closed. D-8 LIMIT CLOSED SCRL AUTO 45 The status of the low fire end switch (M-D) is closed. M-D LIMIT CLOSED SCRL PRESS RESET TO While the control is in STANDBY position (L1-13 OPEN) CLEAR HISTORY pressing and releasing the RESET key will clear current burner hours, cycles and lockout history. MODE AUTO 45 MODE key returns to run message. 24 The EP(D) programmer updates the messages to the ED510 display at least once every 8 seconds. If the ED510 display does not receive information from the EP(D) programmer within 10 seconds the ED510 will display: <strong>FIREYE</strong> ED510 WAITING FOR DATA This can be the result of a defective connection between the programmer and display, defective cable, defective drivers in the programmer or display, or an electrical noise transient causing the EP(D) programmer to cease communication. Removing and restoring power should be executed to recover proper operation. Refer to bulletin SN-100 for recommended techniques for display installation. ®
COMMUNICATIONS The protocol to be used is Modbus RTU. This is implemented by the master (PC, PLC, etc.) issuing a poll to the slave (Flame-Monitor) and the slave responding with the appropriate message. A typical format of a poll request is as follows: DST FNC ADR HI ADR LO DAT HI DST refers to the logical address of the slave. FNC is the function being requested. FNC 03 is a read request. ADR is the message number or register number of the data being requested. In Modbus, register addresses begin at 40001 but is interpreted as address 00. DAT is the number of words being requested. A word is an integer consisting of 2 bytes. The normal response from a slave is as follows: DST FNC DBC DATA…. Hi/Lo DBC is the data byte count being returned. It must be two times the DAT number from the poll request. DATA is the data returned and is always a series of 2 byte integers. If 4 words were requested then DBC would be 8 and there would be 8 data bytes or 4 data words containing the requested data. The format of the data is 4800,N,8,1 meaning 4800 baud, no parity, and 1 stop bit. Below is a table of currently available messages provided by the Flame-Monitor programmers, followed by a description where necessary, EP engineering code 38 or greater and EPD engineering code 4 or greater. DAT LO CRC LO ® CRC LO MESSAGE WORD RESPONSE VALUE ADDRESS REQUESTED 00 1-6 STATUS 83 (053H) = RUN; 202 (0CAH) = LOCKOUT 01 1 MSGN Current message being displayed (see Table 1) 02 1 GSTAT Defines Timer Type 03 1 TIMER Time, Flame, Address 04 1 <strong>FLAME</strong> Flame Signal 05 1-3 LOGSTAT Current logic module, PURGE, PTFI, AUTO (See Table 2) 06 1 INPUTS Input limits state 07 1 OUTPUTS Output relays state 08 2 SYSMINS System on minutes 10 2 BNRMINS Burner on minutes 12 2 CYCLES Completed Burner Cycles 14 1 LOCKOUT COUNT Stored Lockout Count 15 1-6 LOCKOUT HISTORY Last 6 Lockouts, first word is most current lockout 21 1-2 DEVTYP Programmer device type, 5=EP, 6=EPD, 7=MicroM 22 1 AMPTYP Amplifier Type; EUVS4=0C0H; EIR1=0A0H; ERT1, EUV1=090H; CRC HI CRC HI 25
Page 1 and 2: DESCRIPTION E110 with ED510 Display
Page 3 and 4: ELECTRICAL RATINGS APPROVALS LOAD R
Page 5 and 6: 3. SELECT DISPLAY Required for EP P
Page 7 and 8: FLAME SCANNERS 45CM1 45UV5-1009 UV8
Page 9 and 10: INSTALLATION OF CONTROL For a compl
Page 11 and 12: T E R M I N A L S TYPE EP(D)160 M 5
Page 13 and 14: the reset button on the display, th
Page 15 and 16: EP(D)160 LOGIC FLOW DIAGRAM NORMAL
Page 17 and 18: HOLD PURGE 0:00 M-D LIMIT OPEN HOLD
Page 19 and 20: CHECK AUTO 25 LOW FIRE SIGNAL CHECK
Page 21 and 22: LOCKOUT HISTORY The sub-menu “LOC
Page 23: USER PROGRAMMED E300 MESSAGES In ad
Page 27 and 28: EXPLANATION OF LOGSTAT Table 2 LOGI
Page 29 and 30: SYSTEM DIAGNOSTIC MESSAGES 53 35 3-
Page 31 and 32: EXTENDED PREPURGE With EPD programm
Page 33 and 34: OPERATIONAL TEST WARNING: Before te
Page 35 and 36: PILOT BURNER REFRACTORY PILOT FLAME
Page 37 and 38: MAINTENANCE Periodically, the spark
Page 39 and 40: WIRING - UV SCANNERS To connect the
Page 41 and 42: MAINTENANCE 3. Flame rod should ent
Page 43 and 44: 2.75” (70) 2.75” (70) 2.75” (
Page 45 and 46: 1 7/8 (48) 3 7/32 (82) 13/16 HEX (2
Page 48: NOTICE WARRANTIES 48 ® When Fireye

E110 FIREYE FLAME-MONITOR™ - Westmill Industries

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?