associate in arts degree program - St. Louis Community College

47 2010-2011 CATALOG
IV. Electives (either group required) 9 credits
Group A
CE:234 Structural Analysis. . . . . . . . . . . . . . . . . . . . . . . . 3
CE:236 Reinforced Concrete Design. . . . . . . . . . . . . . . 3
CE:237 Structural Steel Design. . . . . . . . . . . . . . . . . . . . 3
Group B
CE:250 Surveying II. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CE:233 Hydraulics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CE:238 Environmental Systems. . . . . . . . . . . . . . . . . . . . 3
Program total . . . . 66-68 credits
** Students who are planning to pursue a BS in Civil
Engineering should take the MTH:185/MTH:210 sequence.
Workplace Experience: Students may substitute up to six
credit hours of appropriate and relevant workplace learning
experience for technical courses, and/or electives, included in the
program. In order for the workplace learning credit to be
counted for the degree requirement, the learning experience
must be pre-approved by the department, and an appropriate
faculty member must supervise the work.
Clinical Laboratory Technology
(Medical Laboratory Technician)
ASSOCIATE IN APPLIED SCIENCE DEGREE
Forest Park
This program prepares students for entry-level positions as
clinical laboratory technicians. Through classroom and practical
experience in hospital and clinical laboratories, students learn to
perform qualitative, quantitative and analytic testing in
microbiology, hematology, blood banking, clinical chemistry,
serology, immunology and routine analysis.
Persons interested in this program should have an interest in
biology, chemistry and the health sciences and be able to follow
precise and detailed instructions.
Graduates are eligible to take the National Certifying Registry
Examination. Positions are available in hospitals, clinics, doctors’
offices, independent laboratories, and public health, research and
industrial laboratories.
I. Career General Education 27 credits
ENG:101 College Composition I . . . . . . . . . . . . . . . . . . . . 3
ENG:102 College Composition II (or)
ENG:xxx English Elective. . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BIO:102 Clinical Physiology . . . . . . . . . . . . . . . . . . . . . . . 3
CHM:101 Fundamentals of Chemistry I . . . . . . . . . . . . . . 5
CHM:212 Bio-Organic and Analytic Chemistry . . . . . . . . 4
MTH:124 Technical Mathematics I . . . . . . . . . . . . . . . . . . . 3
XXX:xxx Missouri State Requirement . . . . . . . . . . . . . . . 3
SOC:101 Introduction to Sociology (or)
XXX:xxx Psychology or Sociology Elective . . . . . . . . . . . 3
II. Physical Education Activity 2 credits
III. Area of Concentration 43 credits
CLT:100 Orientation of the Medical Laboratory . . . . . . 1
CLT:101 Medical Microbiology . . . . . . . . . . . . . . . . . . . . . 3
CLT:102 Routine Analysis . . . . . . . . . . . . . . . . . . . . . . . . . 2
CLT:103 Hematology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CLT:104 Pathogenic Bacteriology I. . . . . . . . . . . . . . . . . . 4
CLT:105 Basic Laboratory Skills . . . . . . . . . . . . . . . . . . . . 4
CLT:200 Pathogenic Bacteriology II . . . . . . . . . . . . . . . . . 4
CLT:201 Clinical Chemistry I. . . . . . . . . . . . . . . . . . . . . . . 5
CLT:202 Clinical Practice I. . . . . . . . . . . . . . . . . . . . . . . . . 4
CLT:204 Blood Bank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
CLT:205 Pathology-Correlation Conference. . . . . . . . . . 1
CLT:206 Clinical Chemistry II . . . . . . . . . . . . . . . . . . . . . . 4
CLT:207 Clinical Practice II . . . . . . . . . . . . . . . . . . . . . . . . 4
CLT:210 Immunology and Serology . . . . . . . . . . . . . . . . . 2
Program total . . . . . . . 72 credits
Computer Aided Design (CAD)
CERTIFICATE OF SPECIALIZATION
Florissant Valley
A CAD operator is able to interpret data from multiple
sources, apply traditional drafting skills, utilize operating system
software, follow industrial practices and company procedures
related to CAD work, and efficiently perform all related tasks to
produce final drawings and CAD models.
Courses 6 credits
EGR:100 Engineering Drawing. . . . . . . . . . . . . . . . . . . . . . 3
GE:101 Technical Computer Applications (or)
GE:121 Principles of Engineering (or)
ESC:100 Engineering Computer Applications
and Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CAD Sequence 9 credits
Select from the following lists with at least one in each area
for a total of at least 9 credit hours:
2-D CAD
EGR:104 Electronic Drafting . . . . . . . . . . . . . . . . . . . . . . . 2
EGR:133 Introduction to AutoCAD I. . . . . . . . . . . . . . . . 2
EGR:140 Computer Aided Drafting and Design I. . . . . . 3
EGR:141 Introduction to AutoCAD II . . . . . . . . . . . . . . . 2
EGR:143 Introduction to Microstation . . . . . . . . . . . . . . . 2
EGR:144 Microstation II . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3-D CAD
EGR:147 Introduction to Engineering Design . . . . . . . . . 3
EGR:145 Computer Solids Modeling . . . . . . . . . . . . . . . . 2
EGR:139 3-D AutoCAD with Autoshade . . . . . . . . . . . . 2
ME:230 Introduction to 3-D Solid Modeling
for Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
EGR:148 Solid Modeling with Unigraphics. . . . . . . . . . . . 2
EGR:256 Solid Modeling with CATIA. . . . . . . . . . . . . . . . 2
CAD Applications
ME:230 Introduction to 3-D Solid Modeling for
Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
EGR:255 Advanced Computer Aided Drafting. . . . . . . . 3
GE:122 Engineering Design and Development. . . . . . . 3
EGR:257 Unigraphics for Part Design. . . . . . . . . . . . . . . . 2
Technical Elective 3 credits
Select course(s) from Engineering and Technology
department (prefixes: BE, CE, EE, EGR, ESC, GE, ME, QC).
Program total . . . . . . . 18 credits