BOILERMATE BOILERMATE - Gledhill Spare Parts

More documents

Recommendations

Info

1.0 DESIGN1.2 TECHNICAL DATAStandard EquipmentThe standard configuration of the BoilerMate2000 is shown opposite. The Appliance ControlBoard (A.C.B.), mounted inside the appliance,controls the operation of the complete system.The A.C.B. is pre-wired to a terminal stripwhere all electrical connections terminate. Itis supplied with the following factory fittedequipment:-1. Boiler pump2. Domestic hot water primary(plate heat exchanger) pump3. Space heating pump4. Hard water appliance control board(A.C.B.)5. Electro-mechanical clock to control thespace heating (in conjunction with roomthermostat - if fitted)6. Plate heat exchanger7. DHWS temperature sensor8. PHE return sensor9. Store temperature sensor10. Y type strainer/flow regulator11. A feed and expansion cisterncomplete with ballvalve, overflowfitting and cold feed/open vent pipeworkassembly is supplied separately.Electro-mechanical clockprogrammerAppliance Control BoardA.C.B.Optional Equipment* A soft water model is available for areaswhere the hardness level is below 200p.p.m. (mg/ltr)* Flexible connectors for quickconnection to first fix pipe installation.For further details see 2.2 Installation,Pipework connections.* ‘Switch’ emergency electrical back-upfor heating and hot water in the eventof a boiler fault.* A seven day digital clock/programmerto control the space heating (inconjunction with a room thermostat iffitted).* A kit to site the clock/programmerremotely.* A no clock option - because of thedesign of the appliance it should not benecessary to fit anything other than asingle channel clock to control theheating system.* Hot and cold water manifolds for use withplastic pipework.Digital clock programmer‘Switch’Page 6
*350mmMin maintenanceaccess to comply withthe Water Regulations1.0 DESIGN1.2 TECHNICAL DATAAPPLIANCE DIMENSIONS300mmF & E CisternModelHeightWidthDepthA B CBM 1251140mm595mm595mmBBM 145BM 185BM 210BM 2251140mm595mm595mm1350mm595mm595mm1500mm595mm595mm1550mm650mm595mmNote: The Appliance dimensions above do not allow forthe100mm high installation baseFAThe following table of minimum cupboard dimensions onlyallow the minimum space required for the appliance (includingthe F & E cistern) and any extra space required for shelving etcin the case of airing cupboards etc must be added.MINIMUM CUPBOARD DIMENSIONSModelHeightWidthDepthF D EEF & E Cisternplan280mmD420mm600mm min clear opening - iflocated directly in front of theappliance.CCUPBOARD600mm 100mmMaintenanceaccessBM 125BM 145BM 185BM 210BM 225Page 71890mm700mm600mm1890mm700mm600mm2100mm700mm600mm2250mm700mm600mm2300mm750mm600mmThe BM 225 is wider than the other sizes and requiresa minimum 686mm wide door and a 750mm widecupboard.Note: The above dimensions are based on the Appliance andthe F & E cistern being in the same cupboard.<strong>BOILERMATE</strong> 2000
Page 1 and 2: BOILERMATE 2000DESIGN, INSTALLATION
Page 3 and 4: 1.0 DESIGN1.1 INTRODUCTIONThese ins
Page 5: 1.0 DESIGN1.2 TECHNICAL DATAWeightW
Page 9 and 10: 1.0 DESIGN1.2 TECHNICAL DATAAWAITIN
Page 11 and 12: 1.0 DESIGN1.3 SYSTEM DETAILSHot and
Page 13 and 14: 1.0 DESIGN1.3 SYSTEM DETAILSPipe Si
Page 15 and 16: 1.0 DESIGN1.3 SYSTEM DETAILSHeating
Page 17 and 18: 1.0 DESIGN1.3 SYSTEM DETAILS‘Swit
Page 19 and 20: 2.0 INSTALLATION2.2 INSTALLATIONPre
Page 21 and 22: 2.0 INSTALLATION2.2 INSTALLATIONIt
Page 23 and 24: 2.0 INSTALLATION2.2 INSTALLATIONEle
Page 25 and 26: 2.0 INSTALLATION2.2 INSTALLATIONWIR
Page 27 and 28: 2.0 INSTALLATION2.3 COMMISSIONINGOp
Page 29 and 30: 2.0 INSTALLATION2.3 COMMISSIONINGNo
Page 31 and 32: 3.0 SERVICING3.1 ANNUAL SERVICINGNo
Page 33 and 34: 3.0 SERVICING1 2 3 45 6 7 891112/13
Page 35 and 36: 3.0 SERVICING P
Page 37 and 38: APPENDIX BMANIFOLDSManifold type: 1
Page 39 and 40: APPENDIX BThe size of the distribut
Page 41 and 42: APPENDIX DPage 41BOILERMATE 2000
Page 43 and 44: APPENDIX E
Page 45: Page 45BOILERMATE 2000

BOILERMATE BOILERMATE - Gledhill Spare Parts

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?