TEL P8 and P8XL Top Load Prober Interface for a ... - Zzybot.net

More documents

Recommendations

Info

TEL P8 and TEL P8XL Top Load Prober Interface Installation Manual for the Catalyst Test SystemInstallation Steps1) Site Preparation2) Installation3) Kinematic Coupler Alignment*4) Docking**Refer to Section 3.6 Kinematic Coupler Alignment and Section 4.4 Docking the TestHead in the Catalyst KCS and Manipulator Manual (pn 553-700-78) for step 3 and 4 above.Unpacking the Interface Assembly KitAssembliesUnpack and inspect the interface assembly kit thoroughly for shipping damage. Verify thematerial against the packing list to make sure that all necessary components are in the kit.If there is damage, or if there are any discrepancies, report it immediately to your localTeradyne field service office before proceeding with the installation.To install interface kits 806-212-XX and 806-214-XX, you need a registration tool kit (pn806-303-00), a V-groove upgrade kit (pn 807-873-00), and an alignment adapter (pn480-047-02).Table 1 through Table 4 list the contents of the TEL P8 and TEL P8XL Top Load ProberInterface Kits. Table 5 lists the contents of the Registration Tool Kit. Table 6 lists thecontents of the V-groove Upgrade Kit and Table 7 lists the contents of the Prober GrooveAlignment Fixture Kit.2
TEL P8 and TEL P8XL Top Load Prober Interface Installation Manual for the Catalyst Test SystemTable 1 I/F, TEL P8 9” Z-HNG, (pn 806-212-01)Quantity Part No. Description1 420-180-01 Assy, Tower, Probe 9”, No Float, Cat.7 470-050-08 4-40 X 3/8” Socket Head Cap Screw5 470-481-05 SCRW SKT HFH M5X.8P/12MM2 480-018-12 Guide Pin, Rough1 480-083-02 TEL P8 L-Plate1 420-232-03 Hinge & Insert1 480-227-12 SPACER, GROOVE A POS, 0.458” thick1 480-227-13 SPACER,GROOVE, B POS, 0.458” thick1 480-227-14 SPACER,GROOVE, C POS, 0.458” thick1 573-038-00 TEL 8P and TEL 8PXL Top Load Prober Interface Manual1 807-873-00 V-Groove Upgrade Kit (See Table 6)3 804-887-00 V-Groove Assembly6 470-046-13 SCRW, CP SKT HD 1/4”-20X1/2”Table 2 I/F, TEL P8 6” Z-HNG (pn 806-212-02)Quantity Part No. Description1 420-228-00 Assy TWR, 6.5”, Probe Catalyst1 420-232-03 Hinge and Insert TEL P86 470-046-13 SCRW, CP, SKT HD1/4”-20X1/2”7 470-050-08 SCRW, CP, SKT HD 4-40X3/8”5 470-481-05 SCRW, SKT FH M5X.8P/12MM2 480-018-12 Guide Pin, Rough1 480-083-02 TEL P8 L-Plate1 480-227-12 Spacer, Groove A Position1 480-227-13 Spacer, Groove BPosition1 480-227-14 Spacer, Groove C Position3 804-887-00 Assy, Groove1 807-873-00 Kit, V-Groove Attachment Upgrade1 573-038-00 TEL 8P and TEL 8PXL Top Load Prober Interface Manual3
Page 1 and 2: TEL P8 and P8XL Top LoadProber Inte
Page 3 and 4: About this ManualTEL P8 and TEL P8X
Page 5: TEL P8 and P8XL Top Load Prober Int
Page 10 and 11: TEL P8 and TEL P8XL Top Load Prober

TEL P8 and P8XL Top Load Prober Interface for a ... - Zzybot.net

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?