beaver

More documents

Recommendations

Info

BEAVER9.6 Angle tracing roller2111126579413438103Angle tracing rollerItemno.Description Q’ty Stock no. Remarks1 Roller arm bracket 1 333542 Bar 1 333553 Roller shaft 2 306704 Roller 1 306715 Roller arm (A) 1 306726 Roller arm shaft 1 306737 Spring 1 333568 Roller arm (B) 1 306759 Nut 1 222.004.462 NL - 810 Screw 1 222.004.121 BH - 10 x 2511 Spring pin 1 222.004.866 PR - 3 x 2212 Spring pin 1 222.004.865 PR - 2 x 2013 Flat Washer 1 222.004.536 WF - 10 x 252
BEAVER10 Cutting Data102 HC (Standard Speed) for AcetylenePlatethicknessTip sizeCuttingspeedOxygen pressure(kg/cm2)FuelgaspressureKerfwidth(mm) (mm/min) Cutting Preheat (kg/cm2) (mm)3 0 680 1.5 1.5 0.2 16 0 610 2 2 0.2 1.310 0 560 2 2 0.2 1.512.5 1 530 2.5 2.5 0.2 1.819 2 460 3 3 0.25 225 2 430 3 3 0.25 238 3 355 3 3 0.25 2.350 4 320 3 3 0.25 2.860 5 280 4 4 0.3 3.075 5 250 4 4 0.3 3.0100 6 200 4 4 0.3 3.6102-D7 (High Speed) for AcetylenePlatethicknessTip sizeCuttingspeedOxygen pressure(kg/cm2)FuelgaspressureKerfwidth(mm) (mm/min) Cutting Preheat (kg/cm2) (mm)3 0 800 7 1,5 0.2 0.86 0 740 7 2 0.2 110 0 680 7 2 0.2 1.312.5 1 630 7 2.5 0.2 1.319 2 560 7 3 0.25 1.525 2 510 7 3 0.25 1.838 3 460 7 3 0.25 250 4 410 7 3 0.25 2.660 5 360 7.0 4.0 0.3 2.875 5 320 7.0 4.0 0.3 2.8100 6 250 7.0 4.0 0.3 3.3Note:1 All pressures are torch inlet pressures2 Oxygen purity is minimum of 99.7%, propane is minimum of JISGrade 3.3 Depending on the surface condition of the steel plate (scale, paint),either increase the fuel gas pressure or decrease cutting speed.Also, when precision cutting is required, adjust all data.53
Page 1 and 2:
BEAVERHANDY AUTOMATIC GAS CUTTING M
Page 3 and 4: BEAVERCONTENTS1 Safety information
Page 5 and 6: BEAVERPREFACEIntroductionThank you
Page 7 and 8: BEAVER1 Safety information1.1 Intro
Page 9 and 10: BEAVER1.3 General Gas cutting safet
Page 11 and 12: BEAVER1.4 Operating and handling sa
Page 13 and 14: BEAVER2 Locations of safety labelsS
Page 15 and 16: BEAVER3 Outline of machine3.1 Featu
Page 17 and 18: BEAVER3.3 SpecificationsTotal weigh
Page 19 and 20: BEAVER4 Preparation for operation4.
Page 21 and 22: BEAVERConnect the JOX with JOX, POX
Page 23 and 24: BEAVER5 Cutting OperationStrictly o
Page 25 and 26: BEAVERPiercing method1 Ignite and a
Page 27 and 28: BEAVERThe jet oxygen valve should b
Page 29 and 30: BEAVERCautionFor the small circle c
Page 31 and 32: BEAVER5.6.5 Bevel cutting1 On bevel
Page 33 and 34: BEAVER6 Maintenance and inspectionR
Page 35 and 36: BEAVER5 The drive motor can be remo
Page 37 and 38: BEAVER7 TroubleshootingRepairs are
Page 39 and 40: BEAVERKnocking Worn gears. ReplaceC
Page 41 and 42: BEAVER8 Wiring diagram and assembly
Page 43 and 44: BEAVER9 Parts list9.1 Main units611
Page 45 and 46: BEAVER9.2 Gear case1523132245422213
Page 47 and 48: BEAVERGear caseItemno.Description Q
Page 49 and 50: BEAVERTorch holder and gas distribu
Page 51 and 52: BEAVERCircle cutting attachmentItem
Page 53: BEAVERAuto stopItemno.Description Q
show all

beaver

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?