DigiTrace 920 Series Heat Trace Controller - Pentair Thermal ...

More documents

Recommendations

Info

Appendix B Typical Enclosure DimensionsB.1 Single-Point Assemblies #10160-003 and #10160-0091 Point FRP1- or 2-pole 30 A SSR assembly1 Pole Model: 920*E2FWL*SIS301*SS31012 Pole Model: 920*E2FWL*SIS301*SS3201The following drawings provide the user with enclosure size and mounting dimensions forthe stock enclosure assemblies. Please contact your local Pentair Thermal Managamentrepresentative for information regarding other available sizes and configurations.6.2533.6810.5012.5013.087.95Mounting holes 0.3" diameter,4 placesDigiTrace ® -AB123467THERMAL MANAGEMENT SOLUTIONS EN-DigiTrace920series-IM-H56874 04/13 62 / 82
B.2 Dual-Point Assemblies #10160-120 and #10160-1212 Point FRP1- or 2-pole 30 A SSR assembly1 Pole Model: 920*E4FWL*SIS302*SS31022 Pole Model: 920*E4FWL*SIS302*SS32028.3118.0012.5514.5514.9410.00Mounting holes 0.3" diameter,4 places123467123467THERMAL MANAGEMENT SOLUTIONS EN-DigiTrace920series-IM-H56874 04/1363 / 82
Page 6 and 7:
Section I - Overview1.1 Controllers
Page 8 and 9:
CSA C/US and c-ETL-us ApprovedThe 9
Page 10 and 11: 1.5.1 ENCLOSURE ASSEMBLYEnclosure A
Page 12 and 13: The user may want to consider enclo
Page 14 and 15: Temperature SensorsTerminal No.Poin
Page 16 and 17: 2.7.6 INPUT POWERThe 920 controller
Page 18 and 19: Section 3 - Programming and Configu
Page 20 and 21: 3.5.2 ALPHANUMERIC TAG ASSIGNMENTPu
Page 22 and 23: Range: 0.3 to 100.0 amps(CURRENT TU
Page 24 and 25: 3.5.15 TS 1 HIGH LIMIT CUTOUTPurpos
Page 26 and 27: IMPORTANT:• Auto-cycling should a
Page 28: 3.6 Common Controller SetupThis is
Page 31 and 32: • This alarm must be enabled and
Page 33 and 34: Procedure: Enable or disable the al
Page 35 and 36: • If the user resets an alarm whi
Page 37 and 38: efore the corresponding alarm will
Page 39 and 40: the overcurrent trip limit and the
Page 41 and 42: the 920 control module, these param
Page 43 and 44: 3.10 Operator Console Functionsbut
Page 45 and 46: eset. All load-shedding parameters
Page 47 and 48: interface.IMPORTANT: The controller
Page 49 and 50: Section 5 - Control Modes5.1 Introd
Page 51 and 52: 5.3 Load Shedding Control ModeLoad
Page 53 and 54: Section 6 - Troubleshooting6.1 Oper
Page 55 and 56: If the bounce or instability is exc
Page 57 and 58: 6.3 Common Alarms—What to look fo
Page 59 and 60: Section 7 - Maintenance7.1 Operator
Page 64 and 65: B.3 Four-Point Assembly #10160-1254
Page 66 and 67: B.5 Twenty-Point Assembly #10160-04
Page 68 and 69: C.1.2 100Ω NICKEL IRON RTD WIRINGC
Page 70 and 71: C.3 Communication Wiring C.3 Commun
Page 72 and 73: C.5 External Input/Output Port Wiri
Page 74 and 75: Appendix E 100 Ω Platinum RTD Tabl
Page 76 and 77: Appendix G Factory Default/Configur
Page 78 and 79: Other Alarms Configuration Sub-Menu
Page 80 and 81: Other Alarms Configuration Sub-Menu
Page 82: WWW.THERMAL.PENTAIR.COMNORTH AMERIC
show all

DigiTrace 920 Series Heat Trace Controller - Pentair Thermal ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?