Safety Standard Certified Ceramic Capacitors/High Voltage ... - Murata

More documents

Recommendations

Info

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.C85E.pdfApr.7,2014DEJ Series Specifications and Test MethodsContinued from the preceding page.No.ItemSpecificationsTest MethodAppearanceNo marked defect16 HumidityLoadingCapacitanceChangeD.F.I.R.Char.EFChar.EF1000MΩ min.Capacitance ChangeWithin ±20%Within ±30%SpecificationsD.F.V5.0%D.F.V7.5%Apply the rated voltage for 500±12 hrs. at 40±2°C in 90 to 95%relative humidity.Pre-treatment:Capacitor should be stored at 85±2°C for 1 hr., then placed atroom condition* 1 for 24±2 hrs. before initial measurements.Post-treatment:Capacitor should be stored for 1 to 2 hrs. at room condition.* 1DielectricStrengthPer Item 6517 LifeAppearanceCapacitanceChangeI.R.DielectricStrengthNo marked defectChar.EF1000MΩ min.Per Item 6Capacitance ChangeWithin ±20%Within ±30%Apply a voltage from Table 2 for 1500 hrs. at 85±2°C, relativehumidity 50% max.Applied VoltageAC500V(r.m.s.), except that once each hour the voltageis increased to AC1000V(r.m.s.) for 0.1 sec.Pre-treatment:Capacitor should be stored at 85±2°C for 1 hr., then placed atroom condition* 1 for 24±2 hrs. before initial measurements.Post-treatment:Capacitor should be stored for 4 to 24 hrs. at room condition.* 118 Flame TestThe capacitor flame discontinued as follows.Cycle1 to 23Time (sec.)15 max.60 max.The capacitor should be subjectedto applied flame for 15 sec. and thenremoved for 15 sec. until 3 cyclesare completed.Gas Burner: Inside Dia. 9.520°7638CapacitorFlame127(in mm)1920RobustnessofTerminationsTemperatureandImmersionCycleTensileBendingAppearanceCapacitanceChangeD.F.I.R.DielectricStrengthLead wire should not be cut off. Capacitor shouldnot be broken.No marked defectChar.EFChar.EF1000MΩ min.Per Item 6Capacitance ChangeWithin ±20%Within ±30%SpecificationsD.F.V5.0%D.F.V7.5%Step1234* 1 "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPaAs shown in the figure at right, fix the body of thecapacitor, apply a tensile weight gradually toeach lead wire in the radial direction of thecapacitor up to 10N and keep it for 10±1 sec.Each lead wire should be subjected to 5N of weight and bent90° at the point of egress, in one direction, then returned to itsoriginal position and bent 90° in the opposite direction at therate of one bend in 2 to 3 sec.The capacitor should be subjected to 5 temperature cycles,then consecutively to 2 immersion cycles.Step12Temperature (ºC)-25+0/-3Room temp.85+3/-0Room temp.TimeTemperature (ºC)(min)65+5/-00±31515Time (min)303303Cycle time: 5 cyclesImmersionWaterCleanwaterSaltwaterCycle time: 2 cyclesPre-treatment:Capacitor should be stored at 85±2˚C for 1 hr., then placed atroom condition* 1 for 24±2 hrs.Post-treatment:Capacitor should be stored for 4 to 24 hrs. at room condition.* 1W22
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.C85E.pdfApr.7,2014Safety Certified Ceramic Capacitors Characteristics Data (Typical Example)c Capacitance - Temperature Characteristics40Cap. Change (%)200-20-40SLBEBSL-60FE-80F-100-40 -20 0 20 40 60 80 100 120 140Temperature (°C)c Insertion Loss - Frequency CharacteristicsType KYType KH0Type KY0Type KH10Signal power: 1mWAC240V(r.m.s.) / 60Hz isapplied on the capacitor.10Signal power: 1mWAC240V(r.m.s.) / 60Hz isapplied on the capacitor.Insertion Loss (dB)203040(7)(5) (4) (3)(6)(1)(2)(1) DE2B3KY101KA2B∗∗∗∗(2) DE2B3KY221KA2B∗∗∗∗(3) DE2B3KY471KA2B∗∗∗∗(4) DE2E3KY102MA2B∗∗∗∗(5) DE2E3KY222MA2B∗∗∗∗(6) DE2E3KY472MA2B∗∗∗∗(7) DE2F3KY103MA3B∗∗∗∗Insertion Loss (dB)203040(7)(5) (4) (3) (2)(6)(1)(1) DE2B3KH101KA3B(2) DE2B3KH221KA3B(3) DE2B3KH471KA3B(4) DE2E3KH102MA3B(5) DE2E3KH222MA3B(6) DE2E3KH472MA3B(7) DE2F3KH103MA3B501 10 100 1000Frequency (MHz)501 10 100 1000Frequency (MHz)Type KX New Small SizeType KX0Type KX New Small Size0Type KXInsertion Loss (dB)10203040(5)(6)(1)(2)(3)(4)501 10 100 1000Frequency (MHz)Signal power: 1mWAC240V(r.m.s.) / 60Hz isapplied on the capacitor.(1) DE1B3KX101KA4BN01F(2) DE1B3KX221KA4BN01F(3) DE1B3KX471KA4BN01F(4) DE1E3KX102MA4BN01F(5) DE1E3KX222MA4BN01F(6) DE1E3KX472MA4BN01FInsertion Loss (dB)102030(1)(2)(4) (3)(5)(6)401 10 100 1000Frequency (MHz)Signal power: 1mWAC240V(r.m.s.) / 60Hz isapplied on the capacitor.(1) DE1B3KX101KA5B(2) DE1B3KX221KA5B(3) DE1B3KX471KA5B(4) DE1E3KX102MA5BA01(5) DE1E3KX222MA5BA01(6) DE1E3KX472MA5BA0123
Page 7 and 8: !Note • Please read rating and !C
Page 23: !Note • Please read rating and !C
Page 75 and 76:
!Note • Please read rating and !C
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
show all

Safety Standard Certified Ceramic Capacitors/High Voltage ... - Murata

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?