Safety Standard Certified Ceramic Capacitors/High Voltage ... - Murata

More documents

Recommendations

Info

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.C85E.pdfApr.7,2014DEB Series Specifications and Test MethodsContinued from the preceding page.No.ItemSpecificationsTest Method9131415Soldering Effect(On-Preheat)Temperatureand ImmersionCycleHumidity (UnderSteady State)16 HumidityLoading17 LifeAppearanceCapacitanceChangeDielectric Strength(Between LeadWires)AppearanceCapacitanceChangeD.F.I.R.Dielectric Strength(Between LeadWires)AppearanceCapacitanceChangeD.F.I.R.AppearanceCapacitanceChangeD.F.I.R.AppearanceCapacitanceChangeD.F.I.R.No marked defectChar. B: Within ±5%Char. E: Within ±15%Char. F: Within ±20%Per item 4.No marked defectChar. B: Within ±10%Char. E: Within ±20%Char. F: Within ±30%Char. B, E: 4.0% max.Char. F: 7.5% max.2000MΩ min.Per item 4.No marked defectChar. B: Within ±10%Char. E: Within ±20%Char. F: Within ±30%Char. B, E: 5.0% max.Char. F: 7.5% max.1000MΩ min.No marked defectChar. B: Within ±10%Char. E: Within ±20%Char. F: Within ±30%Char. B, E: 5.0% max.Char. F: 7.5% max.500MΩ min.No marked defectChar. B: Within ±10%Char. E: Within ±20%Char. F: Within ±30%Char. B, E: 4.0% max.Char. F: 7.5% max.2000MΩ min.First the capacitor should bestored at 120+0/-5°C for60+0/-5 sec.Then, as in the figure, the leadwires should be immersed insolder of 260+0/-5°C up to 1.5 to2.0mm from the root of terminalfor 7.5+0/-1 sec.* "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPaThermalScreenCapacitor1.5to 2.0mmMoltenSolderPre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,then placed at room condition* for 24±2 hrs.before initial measurements.Post-treatment: Capacitor should be stored for 4 to 24 hrs. atroom condition.*The capacitor should be subjected to 5 temperature cycles,then consecutively to 2 immersion cycles.Step Temperature (°C) Time (min)1234-25±3Room Temp.85±3Room Temp.303303Cycle time: 5 cyclesStep Temperature (°C) Time (min) Immersion Water1265+5/-00±31515Clean waterSalt waterCycle time : 2 cyclesPre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,then placed at room condition* for 24±2 hrs.before initial measurements.Post-treatment: Capacitor should be stored for 4 to 24 hrs. atroom condition.*Set the capacitor for 500+24/-0 hrs. at 40±2°C in 90 to 95%relative humidity.Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,then placed at room condition* for 24±2 hrs.before initial measurements.Post-treatment: Capacitor should be stored for 1 to 2 hrs. atroom condition.*Apply the rated voltage for 500+24/-0 hrs. at 40±2°C in 90 to95% relative humidity. (Charge/Discharge currentV50mA)Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,then placed at room condition* for 24±2 hrs.before initial measurements.Post-treatment: Capacitor should be stored at 85±2°C for 1 hr.,then placed at room condition* for 24±2 hrs.Apply a DC voltage of 150% of the rated voltage for1000+48/-0 hrs. at 85±2°C with a relative humidity of 50% max.(Charge/Discharge currentV50mA)Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,then placed at room condition* for 24±2 hrs.before initial measurements.Post-treatment: Capacitor should be stored at 85±2°C for 1 hr.,then placed at room condition* for 24±2 hrs.50
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.C85E.pdfApr.7,2014High Voltage Ceramic CapacitorsDEC Series (Class 1, 2/DC6.3kV)c FeaturesCoated with fl ame-retardant epoxy resin(equivalent to UL94V-0 standard).Please contact us when a halogen-free product*is necessary.* Cl=900ppm max., Br=900ppm max. andCl+Br=1500ppm max.eF±1.0D max.ø dT max.25.0 min.4.0 max.25.0 min.T max.(in mm)c Applications1. Ideal for use as the ballast in backlightinginverters for liquid crystal displays (SL Char.).2. Ideal for use on high voltage circuits such asCockcroft circuits (B Char.).[Bulk]Vertical Crimp Long (Fig. 1)Straight Long (Fig. 2)Lead Code Coating Extension eA3 Up to the end of crimpC43.0 max.ø d0.6±0.050.6±0.05StyleFig. 1Fig. 2Do not use these products in any automotivepower train or safety equipment including batterychargers for electric vehicles and plug-in hybrids.Only Murata products clearly stipulated as"for Automotive use" on its catalog can be usedfor automobile applications such as power train andsafety equipment.c MarkingNominal Body DiameterTemp. Char.SLBEø7mm10J6KVø8-9mm47J6KV66331K6KV6610ø10-15mm151J6KV66B102K6KV66222Z6KV66Temperature CharacteristicsNominal CapacitanceCapacitance ToleranceRated VoltageManufacturer's IdentificationManufactured Date CodeMarked with code for char. B (omitted for nominal body diameter ø9mm and under)Under 100pF: Actual value, 100pF and over: Marked with 3 figuresMarked with codeMarked with code (for DC6.3kV, marked with 6KV)Marked with (omitted for nominal body diameter ø9mm and under)Abbreviation (omitted for nominal body diameter ø7mm)51
Page 7 and 8: !Note • Please read rating and !C
Page 51: !Note • Please read rating and !C

Safety Standard Certified Ceramic Capacitors/High Voltage ... - Murata

Create successful ePaper yourself

Delete template?

Save as template?